2018 Toyota Sienna Suspension & Steering Torque Specs

21 front and rear suspension and steering fasteners are recorded for the 2018 Toyota Sienna. Torque, socket, and thread values are shown only where a cited source verifies them, and none are verified yet. Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2018 Toyota Sienna

On the 2018 Toyota Sienna, the control arms & ball joints fasteners are: Front Lower Ball Joint Nut (specification not verified); Front Lower Control Arm Bolt (Front) (specification not verified); Front Lower Control Arm Bolt (Rear) (specification not verified); Rear Lower Control Arm Bolt (specification not verified); Rear Upper Control Arm Bolt (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2018 Toyota Sienna

On the 2018 Toyota Sienna, the struts, shocks & springs fasteners are: Front Strut Piston Nut (specification not verified); Front Strut Upper Mount Nut (specification not verified); Rear Strut Lower Bolt (specification not verified); Rear Strut Upper Mount Nut (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2018 Toyota Sienna

On the 2018 Toyota Sienna, the sway bar & stabilizer links fasteners are: Front Sway Bar Bracket Bolt (specification not verified); Front Sway Bar Link Nut (specification not verified); Rear Sway Bar Link Nut (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2018 Toyota Sienna

On the 2018 Toyota Sienna, the steering (tie rods & linkage) fasteners are: Electric Power Steering Rack Bolt (specification not verified); Steering Column Universal Joint Bolt (specification not verified); Steering Rack Mount Bolt (specification not verified); Steering Wheel Nut (specification not verified); Tie Rod End Nut (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Other Suspension Fasteners torque — 2018 Toyota Sienna

On the 2018 Toyota Sienna, the other suspension fasteners fasteners are: Front Hub/Bearing Nut (specification not verified); Rear Hub/Bearing Bolt (specification not verified); Subframe Front Mount Bolt (specification not verified); Subframe Rear Mount Bolt (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque Sienna suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…