2019 Hyundai Kona Suspension & Steering Torque Specs

12 front and rear suspension and steering fasteners are recorded for the 2019 Hyundai Kona. Torque, socket, and thread values are shown only where a cited source verifies them, and none are verified yet. Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the control arms & ball joints fasteners are: Front Lower Ball Joint to Knuckle Nut (specification not verified); Front Lower Control Arm to Subframe Bolt (front) (specification not verified); Front Lower Control Arm to Subframe Bolt (rear) (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the struts, shocks & springs fasteners are: Front Strut Rod Nut (specification not verified); Front Strut to Knuckle Bolt (specification not verified); Front Strut Top Mount Nut (specification not verified); Rear Shock Absorber Lower Bolt (specification not verified); Rear Shock Absorber Upper Bolt (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the sway bar & stabilizer links fasteners are: Front Sway Bar Link Nut (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the steering (tie rods & linkage) fasteners are: Outer Tie Rod End Nut (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Wheel Hub & Bearing torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the wheel hub & bearing fasteners are: Front Wheel Hub Bearing Bolt (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Other Suspension Fasteners torque — 2019 Hyundai Kona

On the 2019 Hyundai Kona, the other suspension fasteners fasteners are: Front Subframe Mounting Bolt (specification not verified). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque Kona suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…