2007 BMW 3 Series E90 Lug Nut Torque & Bolt Specs

The 2007 BMW 3 Series E90 lug nut torque is 103 ft-lbs (140 Nm). Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 103 ft-lbs (140 Nm).

This page is the OEM-referenced fastener summary for the 2007 BMW 3 Series E90. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2007 BMW 3 Series E90, fasteners follow metric standards typical of mid-2000s BMW engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2007 BMW 3 Series E90

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2007 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2007 BMW 3 Series E90?

The OEM-specified lug-nut torque for the 2007 BMW 3 Series E90 is 103 ft-lbs (140 Nm). Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2007 BMW 3 Series E90 lug nuts?

Most modern BMW vehicles use a 19mm or 21mm socket. Older BMW models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2007 BMW 3 Series E90 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other BMW 3 Series E90 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2007 BMW 3 Series E90 oil drain plug torque & size

All 4 2007 BMW 3 Series E90 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2007 BMW 3 Series E90, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 4 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2007 BMW 3 Series E90

Wheel and lug nut spec for the 2007 BMW 3 Series E90. For the all wheels, plan for the right driver; final torque is 103 ft-lbs (140 Nm) (wheel bolt). Confirmed against manufacturer service literature.

Engine — 2007 BMW 3 Series E90

Engine bolt-by-bolt torque for the 2007 BMW 3 Series E90, including the long block, valve covers, and intake. Oil drain plug tightens to 18 ft-lbs (24 Nm), located at the oil pan. This figure is independently verified against OEM service data.

Drivetrain — 2007 BMW 3 Series E90

Drivetrain and driveline fasteners for the 2007 BMW 3 Series E90 — axle, transmission, and differential plugs. The transmission pan bolts uses a 10mm drive on a M8 x 1.25 thread, torqued to 10 Nm (7 ft-lbs) at the drivetrain. At the drivetrain, the differential drain plug torques to 60 Nm (44 ft-lbs) (17mm drive, M14 x 1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2007 BMW 3 Series E90 numbers above.

Loading the interactive 2007 BMW 3 Series E90 fastener lookup with per-bolt filtering, part links, and torque tools…