2024 Buick Envision Lug Nut Torque & Bolt Specs

The 2024 Buick Envision lug nut torque is 140 ft-lbs (190 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 140 ft-lbs (190 Nm) · Socket size: 22mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2024 Buick Envision. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

GM lug-nut torque clusters around 140 ft-lbs (190 Nm) for half-ton Silverado/Sierra and 100 ft-lbs for passenger cars like Malibu, Impala, and Cruze. GM heavy-duty trucks (2500HD/3500HD) jump to 165 ft-lbs. Most GM passenger cars use a 19mm socket; trucks moved from 22mm to 22mm-with-deep-well in 2014. Watch for GM's flat-flange lug nut design on the Silverado — the standard cone-seat aftermarket lugs will not seat correctly.

Common fastener categories on the 2024 Buick Envision

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Buick Envision?

The OEM-specified lug-nut torque for the 2024 Buick Envision is 140 ft-lbs (190 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Buick Envision lug nuts?

The 2024 Buick Envision uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Buick Envision fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Buick Envision years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Buick Envision oil drain plug torque & size

→ 2024 Buick Envision suspension & steering torque specs (control arm, ball joint, tie rod)

All 12 2024 Buick Envision fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Buick Envision, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2024 Buick Envision

Brake fasteners on the 2024 Buick Envision — caliper bracket, slide pins, and banjo bolt torque follow. For the front, plan for a 13mm tool on a M8x1.25 stud; final torque is 26 ft-lbs (35 Nm) (front caliper slide pin). Front caliper bracket bolt tightens to 137 ft-lbs (186 Nm), takes a 18mm driver, runs on M12x1.5 threads, located at the front. The rear caliper bracket bolt uses a 18mm drive on a M12x1.5 thread, torqued to 85 ft-lbs (115 Nm) at the rear. At the rear, the rear caliper slide pin torques to 26 ft-lbs (35 Nm) (13mm drive, M8x1.25 thread).

Engine — 2024 Buick Envision

Engine bolt-by-bolt torque for the 2024 Buick Envision, including the long block, valve covers, and intake. Spark plug tightens to 15 ft-lbs (20 Nm), takes a 5/8 in. driver, runs on M14x1.25 threads. The oil filter uses a 32mm cap drive, torqued to 22 ft-lbs (30 Nm). The oil drain plug torques to 18 ft-lbs (25 Nm) (15mm drive, M12x1.75 thread).

Suspension — 2024 Buick Envision

Suspension and chassis fastener torque for the 2024 Buick Envision — strut, control arm, and sway bar values. The rear lower control arm bolt uses a 18mm drive on a M12x1.5 thread, torqued to 85 ft-lbs (115 Nm) at the rear. At the front, the front lower control arm bolt torques to 111 ft-lbs (150 Nm) (21mm drive, M14x1.5 thread). For the front, plan for a 15mm tool on a M12x1.5 stud; final torque is 37 ft-lbs (50 Nm) (front strut top nut).

Wheels & Tires — 2024 Buick Envision

Wheels & Tires fasteners on the 2024 Buick Envision. The lug nut torques to 140 ft-lbs (190 Nm) (22mm drive, M14x1.5 thread).

Transmission — 2024 Buick Envision

Transmission fasteners on the 2024 Buick Envision. plan for a 10mm hex tool on a M14x1.5 stud; final torque is 18 ft-lbs (25 Nm) (transmission drain plug).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Buick Envision numbers above.

Loading the interactive 2024 Buick Envision fastener lookup with per-bolt filtering, part links, and torque tools…