2015–2016 Buick Lacrosse Bolt Sizes & Torque Specs

Lug nut torque is not verified for this summary. Review the cited evidence and exact hardware application before installation.

Where these numbers come from

1 value for the 2016 Buick Lacrosse is checked against a maker’s document. Each row names the document, the page or section and the manual’s own wording, so you can check it yourself.

SpecValueDocument and pageManual wordingApplies to
Valve Cover Bolt — torque89 in-lbs (10 Nm)GM-attributed 2016 Buick LaCrosse service information mirror (LEMON Manuals): 2.4L I4 eAssist, Camshaft Cover Replacement (on vehicle); Fastener Specifications table · lemon-manuals.la“Camshaft Cover Fastener (Qty: 11) ... Tighten 10 N.m (89 lb in) | Spec table: Cam Cover to Cylinder Head Bolt | 10 N.m | 89 lb in”Original GM camshaft cover bolts on the 2016 LaCrosse, every engine offered that year. All print 10 N.m (89 lb in). 2.4L I4 eAssist: "Camshaft Cover Fastener (Qty: 11) ... Tighten 10 N.m (89 lb in)"; 3.6L V6: "Tighten the left camshaft cover bolts in the sequence shown to 10 N.m (89 lb in)". New gasket/grommets per GM. Not aftermarket covers. Applies to: trim: 2nd Gen (1 configuration).

Latest proof checked 2026-10-30. Values that changed after a check are listed in the corrections log.

Tools for this job

Matched to the specs on this page.

As an Amazon Associate I earn from qualifying purchases. Tool picks are general options, not a fit guarantee for your vehicle or fastener.

Every value on this page for the 2016 Buick Lacrosse names the document it was checked against. Match the exact hardware and manual conditions before maintenance. A source for one field does not verify the other specifications.

These specifications also apply to the 2015 model years — identical specs on file for each year.

Frequently asked questions

Are the 2016 Buick Lacrosse fasteners metric or SAE?

Metric and SAE hardware can both appear on one vehicle, depending on the component and exact application. Use the individually verified field and the actual fastener or service manual rather than inferring a standard from the model year, make or generation. Bolt-head markings can help identify the hardware at the bench.

Not yet verified for the 2016 Buick Lacrosse: lug nut torque and lug nut socket size. Check your owner’s or service manual, or ask a dealer. Send a correction

Other Buick Lacrosse years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2016 Buick Lacrosse suspension & steering torque specs (control arm, ball joint, tie rod)

Fasteners on record for the 2016 Buick Lacrosse

1 of the 13 fasteners on record for the 2016 Buick Lacrosse has at least one value checked against a maker’s document; each sentence below names it. A checked torque does not confirm the socket size, thread or part number. Where sources disagree, the value is withheld.

Engine — 2016 Buick Lacrosse

Engine fasteners checked against a maker’s document for the 2016 Buick Lacrosse. Valve Cover Bolt (Camshaft (valve) cover to cylinder head). Torque: 89 in-lbs (10 Nm). Source: GM-attributed 2016 Buick LaCrosse service information mirror (LEMON Manuals): 2.4L I4 eAssist, Camshaft Cover Replacement (on vehicle); Fastener Specifications table. Original GM camshaft cover bolts on the 2016 LaCrosse, every engine offered that year. All print 10 N.m (89 lb in). 2.4L I4 eAssist: "Camshaft Cover Fastener (Qty: 11) ... Tighten 10 N.m (89 lb in)"; 3.6L V6: "Tighten the left camshaft cover bolts in the sequence shown to 10 N.m (89 lb in)". New gasket/grommets per GM. Not aftermarket covers. trim: 2nd Gen

Also on record but not yet checked against a maker’s document (12): Front Caliper Bracket Bolt, Front Caliper Slide Pin, Front Lower Control Arm Bolt, Front Strut Top Nut, Lug Nut, Oil Drain Plug, Oil Filter, Rear Caliper Bracket Bolt, Rear Caliper Slide Pin, Rear Lower Control Arm Bolt, Spark Plug, Transmission Drain Plug. Their stored figures are not shown until a document confirms them. Have the factory figure? Send a correction.

Valve cover fastener locations and tightening sequence — 2016 Buick Lacrosse

2.4L 4-cylinder: 89 in-lbs (10 Nm)

  1. 11 cover bolts, all tightened to 89 in-lbs (10 Nm).
  2. GM gives no tightening order: start every bolt by hand, then tighten each one to 89 in-lbs (10 Nm).
  3. Fit a new cover gasket and new cover grommets (and new bolts, if your bolts come with the grommet).

Source: GM service information (Buick LaCrosse, Regal and Verano, 2.4L): Camshaft Cover Replacement, Fastener Specifications.

V6 (3.0L or 3.6L): 89 in-lbs (10 Nm)

Right cover (bank 1): 13 bolts
12345678910111213
Left cover (bank 2): 13 bolts
12345678910111213
  1. Two covers, 13 bolts each.
  2. Fit new bolt grommets, then start every bolt by hand.
  3. Tighten in the numbered order to 89 in-lbs (10 Nm). This is GM's engine-in-car order; GM's engine-out procedure numbers the covers differently.
  4. Put an 8 mm wide, 4 mm high bead of RTV sealant on the engine front cover split lines before setting each cover down.

Other fasteners on this cover (studs, coil and bracket bolts):

  • Ball stud on the left cover for the plastic fuel-injector cover: 89 in-lbs (10 Nm)

Source: GM service information (Buick LaCrosse V6): Camshaft Cover Replacement, Left Side and Right Side.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then compare any source-backed fields on this page with the actual hardware and service manual.

Loading the interactive 2016 Buick Lacrosse fastener lookup with per-bolt filtering, part links, and torque tools…