2015 Cadillac Ats Lug Nut Torque & Bolt Specs

The 2015 Cadillac Ats lug nut torque is 100 ft-lbs (135 Nm), tightened with a 17mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 17mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2015 Cadillac Ats. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

GM lug-nut torque clusters around 140 ft-lbs (190 Nm) for half-ton Silverado/Sierra and 100 ft-lbs for passenger cars like Malibu, Impala, and Cruze. GM heavy-duty trucks (2500HD/3500HD) jump to 165 ft-lbs. Most GM passenger cars use a 19mm socket; trucks moved from 22mm to 22mm-with-deep-well in 2014. Watch for GM's flat-flange lug nut design on the Silverado — the standard cone-seat aftermarket lugs will not seat correctly.

Common fastener categories on the 2015 Cadillac Ats

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2015 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2015 Cadillac Ats?

The OEM-specified lug-nut torque for the 2015 Cadillac Ats is 100 ft-lbs (135 Nm), using a 17mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2015 Cadillac Ats lug nuts?

The 2015 Cadillac Ats uses a 17mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2015 Cadillac Ats fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Cadillac Ats years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2015 Cadillac Ats oil drain plug torque & size

→ 2015 Cadillac Ats suspension & steering torque specs (control arm, ball joint, tie rod)

All 12 2015 Cadillac Ats fastener specs

Per-bolt torque, wrench size, and thread spec for the 2015 Cadillac Ats, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 12 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Brakes — 2015 Cadillac Ats

Brake fasteners on the 2015 Cadillac Ats — caliper bracket, slide pins, and banjo bolt torque follow. The rear caliper bracket bolt uses a 18mm drive on a M12x1.5 thread, torqued to 85 ft-lbs (115 Nm) at the rear. At the rear, the rear caliper slide pin torques to 26 ft-lbs (35 Nm) (13mm drive, M8x1.25 thread). For the front, plan for a 18mm tool on a M12x1.5 stud; final torque is 137 ft-lbs (186 Nm) (front caliper bracket bolt). Front caliper slide pin tightens to 26 ft-lbs (35 Nm), takes a 13mm driver, runs on M8x1.25 threads, located at the front.

Engine — 2015 Cadillac Ats

Engine bolt-by-bolt torque for the 2015 Cadillac Ats, including the long block, valve covers, and intake. The oil drain plug torques to 18 ft-lbs (25 Nm) (15mm drive, M12x1.75 thread). plan for a 5/8 in. tool on a M14x1.25 stud; final torque is 15 ft-lbs (20 Nm) (spark plug). Oil filter tightens to 22 ft-lbs (30 Nm), takes a 32mm cap driver. This figure is independently verified against OEM service data.

Suspension — 2015 Cadillac Ats

Suspension and chassis fastener torque for the 2015 Cadillac Ats — strut, control arm, and sway bar values. For the rear, plan for a 18mm tool on a M12x1.5 stud; final torque is 74 ft-lbs (100 Nm) (rear lower control arm bolt). Front lower control arm bolt tightens to 74 ft-lbs (100 Nm), takes a 18mm driver, runs on M12x1.5 threads, located at the front. The front strut top nut uses a 15mm drive on a M12x1.5 thread, torqued to 37 ft-lbs (50 Nm) at the front.

Wheels & Tires — 2015 Cadillac Ats

Wheels & Tires fasteners on the 2015 Cadillac Ats. Lug nut tightens to 100 ft-lbs (135 Nm), takes a 17mm driver, runs on M12x1.5 threads.

Transmission — 2015 Cadillac Ats

Transmission fasteners on the 2015 Cadillac Ats. The transmission drain plug uses a 10mm hex drive on a M14x1.5 thread, torqued to 18 ft-lbs (25 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2015 Cadillac Ats numbers above.

Loading the interactive 2015 Cadillac Ats fastener lookup with per-bolt filtering, part links, and torque tools…