2016 Can Am Defender Lug Nut Torque & Bolt Specs

The 2016 Can Am Defender lug nut torque is 50 ft-lbs, tightened with a 3/4" socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 50 ft-lbs · Socket size: 3/4" · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2016 Can Am Defender. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2016 Can Am Defender, fasteners follow metric standards typical of late-model Can Am engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2016 Can Am Defender

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2016 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2016 Can Am Defender?

The OEM-specified lug-nut torque for the 2016 Can Am Defender is 50 ft-lbs, using a 3/4" socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2016 Can Am Defender lug nuts?

The 2016 Can Am Defender uses a 3/4" socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2016 Can Am Defender fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Can Am Defender years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2016 Can Am Defender oil drain plug torque & size

All 4 2016 Can Am Defender fastener specs

Per-bolt torque, wrench size, and thread spec for the 2016 Can Am Defender, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2016 Can Am Defender

Wheel and lug nut spec for the 2016 Can Am Defender. The lug nut uses a 3/4" drive on a M12x1.5 thread, torqued to 50 ft-lbs at the wheels.

Engine — 2016 Can Am Defender

Engine bolt-by-bolt torque for the 2016 Can Am Defender, including the long block, valve covers, and intake. At the engine, the oil drain plug torques to 22 ft-lbs (27mm drive, M20x1.5 thread). For the engine, plan for a 5/8" tool on a M10x1.0 stud; final torque is 10-14 ft-lbs (spark plug).

Drivetrain — 2016 Can Am Defender

Drivetrain and driveline fasteners for the 2016 Can Am Defender — axle, transmission, and differential plugs. For the drivetrain, plan for a 22mm tool on a M16x1.5 stud; final torque is 18 ft-lbs (differential fill plug).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2016 Can Am Defender numbers above.

Loading the interactive 2016 Can Am Defender fastener lookup with per-bolt filtering, part links, and torque tools…