1992 Case 1835c Lug Nut Torque & Bolt Specs

The 1992 Case 1835c lug nut torque is 125 ft-lbs, tightened with a 19mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 125 ft-lbs · Socket size: 19mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 1992 Case 1835c. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 1992 Case 1835c, fasteners follow metric standards typical of 1990s-era Case engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 1992 Case 1835c

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1992 Case 1835c owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1992 Case 1835c?

The OEM-specified lug-nut torque for the 1992 Case 1835c is 125 ft-lbs, using a 19mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1992 Case 1835c lug nuts?

The 1992 Case 1835c uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1992 Case 1835c fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Case 1835c years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1992 Case 1835c oil drain plug torque & size

All 24 1992 Case 1835c fastener specs

Per-bolt torque, wrench size, and thread spec for the 1992 Case 1835c, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 1992 Case 1835c

Engine bolt-by-bolt torque for the 1992 Case 1835c, including the long block, valve covers, and intake. The injection pump bolt uses a 17mm drive on a M12x1.75 thread, torqued to 65 ft-lbs at the engine block. At the oil pan, the oil pan bolt torques to 20 ft-lbs (13mm drive, M8x1.25 thread). For the oil pan, plan for a 17mm tool on a M14x1.5 stud; final torque is 45 ft-lbs (oil drain plug). Fan pulley bolt tightens to 85 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the crankshaft. The valve cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the valve cover.

Body — 1992 Case 1835c

Body fasteners on the 1992 Case 1835c. At the floor, the seat base bolt torques to 65 ft-lbs (17mm drive, M12x1.75 thread). For the frame, plan for a 13mm tool on a M8x1.25 stud; final torque is 25 ft-lbs (belly pan bolt). Door hinge bolt tightens to 25 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the cab frame.

Electrical — 1992 Case 1835c

Electrical fasteners on the 1992 Case 1835c. For the tensioner body, plan for a 12mm tool on a M8x1.25 stud; final torque is 22 ft-lbs (belt tensioner lock bolt). Starter support bracket bolt tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the block/transmission. The idler pulley bolt uses a 15mm drive on a M10x1.5 thread, torqued to 35 ft-lbs at the bracket. At the bell housing, the starter mounting bolt torques to See sequence (14mm drive, M10x1.25 thread).

Hydraulic — 1992 Case 1835c

Hydraulic fasteners on the 1992 Case 1835c. Hydraulic motor bolt tightens to 85 ft-lbs, takes a 17mm driver, runs on M12x1.75 threads, located at the motor mount. The hydraulic pump bolt uses a 13mm drive on a M8x1.25 thread, torqued to 35 ft-lbs at the pump mount. At the various, the hydraulic line fitting torques to 45 ft-lbs (22mm drive, M16x1.5 thread). For the valve block, plan for a 13mm tool on a M8x1.25 stud; final torque is 25 ft-lbs (control valve bolt).

Drive — 1992 Case 1835c

Drive fasteners on the 1992 Case 1835c. The wheel bolt uses a 19mm drive on a M14x1.5 thread, torqued to 125 ft-lbs at the wheel hub. At the chain case, the chain case cover bolt torques to 25 ft-lbs (13mm drive, M8x1.25 thread). For the drive motor, plan for a 24mm tool on a M16x2.0 stud; final torque is 275 ft-lbs (drive sprocket bolt). Drive motor bolt tightens to 110 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the chain case.

Loader — 1992 Case 1835c

Loader fasteners on the 1992 Case 1835c. At the cylinder end, the cylinder pin lock torques to 110 ft-lbs (19mm drive, M14x2.0 thread). For the frame, plan for a 32mm tool on a Press Fit stud; final torque is N/A — Press Fit (loader arm pivot pin). Bucket pivot pin tightens to N/A — Press Fit, takes a 27mm driver, runs on Press Fit threads, located at the loader arms. The quick attach pin uses a 24mm drive on a Press Fit thread, torqued to N/A — Press Fit at the attachment plate.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1992 Case 1835c numbers above.

Loading the interactive 1992 Case 1835c fastener lookup with per-bolt filtering, part links, and torque tools…