2015 Case 580n Bolt Sizes & Torque Specs
Lug nut torque is not verified for this summary. Review the cited evidence and exact hardware application before installation.
Every value on this page for the 2015 Case 580n names the document it was checked against. Match the exact hardware and manual conditions before maintenance. A source for one field does not verify the other specifications.
For the 2015 Case 580n, fasteners follow application-specific metric or SAE standards typical of late-model Case engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).
Common fastener categories on the 2015 Case 580n
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket, mounting, and slide/guide-pin bolts are different fasteners. Confirm the exact axle, application and service-manual specification before reassembly.
- Engine oil drain plug torque and tool size when this vehicle has a verified drain-plug record
- Transmission pan, valve cover, and intake manifold bolts where the database has exact records
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque only when a vehicle-specific spark-plug row is available
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
For 2015 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.
Tools you will need
- Metric and SAE socket set (8mm-22mm plus 1/4"-7/8"), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Replacement washers, threadlocker, anti-seize, or dry-thread preparation only when the exact service procedure specifies them
Frequently asked questions
Are the 2015 Case 580n fasteners metric or SAE?
Metric and SAE hardware can both appear on one vehicle, depending on the component and exact application. Use the individually verified field and the actual fastener or service manual rather than inferring a standard from the model year, make or generation. Bolt-head markings can help identify the hardware at the bench.
Not yet verified for the 2015 Case 580n: lug nut torque and lug nut socket size. Check your owner’s or service manual, or ask a dealer. Send a correction
Other Case 580n years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
- 2021 Case 580n lug nut torque
- 2020 Case 580n lug nut torque
- 2019 Case 580n lug nut torque
- 2018 Case 580n lug nut torque
- 2017 Case 580n lug nut torque
- 2016 Case 580n lug nut torque
- 2014 Case 580n lug nut torque
- 2013 Case 580n lug nut torque
- 2012 Case 580n lug nut torque
- 2011 Case 580n lug nut torque
- 2010 Case 580n lug nut torque
- 2009 Case 580n lug nut torque
- 2008 Case 580n lug nut torque
Fasteners on record for the 2015 Case 580n
None of the 7 fasteners on record for the 2015 Case 580n has a value checked against a maker’s document yet, so no figures are shown.
Also on record but not yet checked against a maker’s document (7): Backhoe Boom Pivot Bolt, Engine Oil Drain Plug, Front Wheel Lug Nut, Loader Boom Pivot Bolt, Rear Wheel Lug Nut, ROPS Cab Mounting Bolt, Stabilizer Leg Pin Retaining Bolt. Their stored figures are not shown until a document confirms them. Have the factory figure? Send a correction.
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then compare any source-backed fields on this page with the actual hardware and service manual.
Loading the interactive 2015 Case 580n fastener lookup with per-bolt filtering, part links, and torque tools…