2017 Caterpillar 303.5e2 Cr Bolt Sizes & Torque Specs

Free OEM-referenced torque and bolt specs for the 2017 Caterpillar 303.5e2 Cr.

This page is the OEM-referenced fastener summary for the 2017 Caterpillar 303.5e2 Cr. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2017 Caterpillar 303.5e2 Cr, fasteners follow metric standards typical of late-model Caterpillar engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2017 Caterpillar 303.5e2 Cr

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2017 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2017 Caterpillar 303.5e2 Cr?

Manufacturer-specified torque values for the 2017 Caterpillar 303.5e2 Cr are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Caterpillar brand page for the closest model year.

What socket size do I need for the 2017 Caterpillar 303.5e2 Cr lug nuts?

Most modern Caterpillar vehicles use a 19mm or 21mm socket. Older Caterpillar models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2017 Caterpillar 303.5e2 Cr fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Caterpillar 303.5e2 Cr years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2017 Caterpillar 303.5e2 Cr oil drain plug torque & size

All 6 2017 Caterpillar 303.5e2 Cr fastener specs

Per-bolt torque, wrench size, and thread spec for the 2017 Caterpillar 303.5e2 Cr, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2017 Caterpillar 303.5e2 Cr

Engine bolt-by-bolt torque for the 2017 Caterpillar 303.5e2 Cr, including the long block, valve covers, and intake. The engine oil drain plug (cat c1.1) uses a 17mm drive on a M14x1.5 thread, torqued to 22–25 ft-lbs (30–34 Nm) at the engine oil sump.

Drivetrain — 2017 Caterpillar 303.5e2 Cr

Drivetrain and driveline fasteners for the 2017 Caterpillar 303.5e2 Cr — axle, transmission, and differential plugs. At the final drive gear box (one per side), the final drive drain plug torques to 29–36 ft-lbs (40–49 Nm) (22mm drive, M16x1.5 thread).

Attachment — 2017 Caterpillar 303.5e2 Cr

Attachment fasteners on the 2017 Caterpillar 303.5e2 Cr. For the bucket pin lock bolt, plan for a 18mm tool on a M12x1.75 stud; final torque is 75 ft-lbs (102 Nm) (bucket pin retaining bolt).

Undercarriage — 2017 Caterpillar 303.5e2 Cr

Undercarriage fasteners on the 2017 Caterpillar 303.5e2 Cr. Track shoe bolt tightens to 130–155 ft-lbs (177–210 Nm), takes a 24mm driver, runs on M16x1.5 threads, located at the track shoes — 3 bolts per shoe, both sides. The swing bearing bolt uses a 22mm drive on a M14x2.0 thread, torqued to 100 ft-lbs (136 Nm) at the swing bearing ring.

Safety — 2017 Caterpillar 303.5e2 Cr

Safety fasteners on the 2017 Caterpillar 303.5e2 Cr. The rops mounting bolt uses a 22mm drive on a M14x2.0 thread, torqued to 100 ft-lbs (136 Nm) at the rops canopy to upper frame (4 bolts).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2017 Caterpillar 303.5e2 Cr numbers above.

Loading the interactive 2017 Caterpillar 303.5e2 Cr fastener lookup with per-bolt filtering, part links, and torque tools…