1967 Chevrolet Corvette Lug Nut Torque & Bolt Specs

The 1967 Chevrolet Corvette lug nut torque is 100 ft-lbs (135 Nm) on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 1967 Chevrolet Corvette. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

GM lug-nut torque clusters around 140 ft-lbs (190 Nm) for half-ton Silverado/Sierra and 100 ft-lbs for passenger cars like Malibu, Impala, and Cruze. GM heavy-duty trucks (2500HD/3500HD) jump to 165 ft-lbs. Most GM passenger cars use a 19mm socket; trucks moved from 22mm to 22mm-with-deep-well in 2014. Watch for GM's flat-flange lug nut design on the Silverado — the standard cone-seat aftermarket lugs will not seat correctly.

Common fastener categories on the 1967 Chevrolet Corvette

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1967 Chevrolet Corvette owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

SAE socket set (1/4"-7/8"), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1967 Chevrolet Corvette?

The OEM-specified lug-nut torque for the 1967 Chevrolet Corvette is 100 ft-lbs (135 Nm) on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1967 Chevrolet Corvette lug nuts?

Most modern Chevrolet vehicles use a 19mm or 21mm socket. Older Chevrolet models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 1967 Chevrolet Corvette fasteners metric or SAE?

SAE inch is the standard for this vehicle. Most fasteners on this vehicle are SAE inch, common sizes 1/4", 5/16", 3/8", 7/16", 1/2". Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Chevrolet Corvette years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1967 Chevrolet Corvette oil drain plug torque & size

→ 1967 Chevrolet Corvette suspension & steering torque specs (control arm, ball joint, tie rod)

All 28 1967 Chevrolet Corvette fastener specs

Per-bolt torque, wrench size, and thread spec for the 1967 Chevrolet Corvette, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 1967 Chevrolet Corvette

Wheel and lug nut spec for the 1967 Chevrolet Corvette. The lug nut is a M12x1.5 thread, torqued to 100 ft-lbs (135 Nm) at the all wheels.

Brakes — 1967 Chevrolet Corvette

Brake fasteners on the 1967 Chevrolet Corvette — caliper bracket, slide pins, and banjo bolt torque follow. At the caliper to bracket, the brake caliper mounting bolt torques to 70 ft-lbs (7/16" drive, 20 TPI thread).

Engine — 1967 Chevrolet Corvette

Engine bolt-by-bolt torque for the 1967 Chevrolet Corvette, including the long block, valve covers, and intake. For the valve cover - sbc/bbc, plan for a 7/16" tool on a 5/16-18 stud; final torque is 4 ft-lbs (valve cover bolt). Water pump bolt tightens to 15 ft-lbs, takes a 1/2" driver, runs on 3/8-16 threads, located at the water pump to block. The spark plug (bb) uses a 5/8" drive on a 14mm-1.25 thread, torqued to 25 ft-lbs at the cylinder head - 427 bbc. At the oil pan, the oil drain plug torques to 18 ft-lbs (25 Nm) (M12x1.75 thread). For the cylinder head rocker studs - sbc, plan for a 9/16" tool on a 7/16-14 stud; final torque is 50 ft-lbs (rocker arm stud (sb)). Oil pan bolt tightens to 12 ft-lbs, takes a 7/16" driver, runs on 5/16-18 threads, located at the oil pan - sbc/bbc. The connecting rod bolt (bb) uses a 9/16" drive on a 7/16-20 thread, torqued to 50 ft-lbs at the connecting rod caps - 427 bbc. At the intake manifold - sbc/bbc, the intake manifold bolt torques to 25 ft-lbs (9/16" drive, 3/8-16 thread). For the cylinder head - 327 sbc, plan for a 5/8" tool on a 14mm-1.25 stud; final torque is 25 ft-lbs (spark plug (sb)). Engine mount to frame bolt tightens to 35 ft-lbs, takes a 9/16" driver, runs on 3/8-16 threads, located at the engine mount to frame bracket. The main bearing cap bolt (bb) uses a 5/8" drive on a 1/2-13 thread, torqued to 95 ft-lbs at the main bearing caps - 427 bbc.

Suspension — 1967 Chevrolet Corvette

Suspension and chassis fastener torque for the 1967 Chevrolet Corvette — strut, control arm, and sway bar values. Rear spring to differential cover bolt tightens to 65 ft-lbs, takes a 9/16" driver, runs on 18 TPI threads, located at the transverse leaf spring center mount. The rear strut rod bolt uses a 3/4" drive on a 1/2-13 thread, torqued to 75 ft-lbs at the rear irs strut rod pivot. At the front shock absorber upper mount, the front shock absorber upper nut torques to 25 ft-lbs (9/16" drive, 3/8-24 thread). For the rear irs trailing arm pivot, plan for a 3/4" tool on a 1/2-13 stud; final torque is 85 ft-lbs (rear trailing arm bolt).

Body — 1967 Chevrolet Corvette

Body fasteners on the 1967 Chevrolet Corvette. The door hinge to pillar bolt uses a 3/8" drive on a 16 TPI thread, torqued to 25 ft-lbs at the a-pillar hinge mount. At the hood hinge to hood panel, the hood hinge to hood bolt torques to 10 ft-lbs (7/16" drive, 5/16-18 thread).

Exhaust — 1967 Chevrolet Corvette

Exhaust fasteners on the 1967 Chevrolet Corvette. At the exhaust header to cylinder head, the exhaust header bolt torques to 20 ft-lbs (9/16" drive, 3/8-16 thread).

Electrical — 1967 Chevrolet Corvette

Electrical fasteners on the 1967 Chevrolet Corvette. For the alternator bracket to block, plan for a 1/2" tool on a 3/8-16 stud; final torque is 25 ft-lbs (alternator mounting bolt).

Cylinder Head — 1967 Chevrolet Corvette

Cylinder Head fasteners on the 1967 Chevrolet Corvette. Cylinder head bolt (sb) tightens to 65 ft-lbs, takes a 7/16" driver, runs on 14 TPI threads, located at the head to block. The cylinder head bolt (bb) uses a 1/2" drive on a 13 TPI thread, torqued to 75 ft-lbs at the head to block.

Engine Block — 1967 Chevrolet Corvette

Engine Block fasteners on the 1967 Chevrolet Corvette. The harmonic balancer bolt uses a 7/8" drive on a 16 TPI thread, torqued to 60 ft-lbs at the crankshaft snout. At the flywheel to crank, the flywheel to crankshaft bolt torques to 60 ft-lbs (7/16" drive, 20 TPI thread).

Fuel System — 1967 Chevrolet Corvette

Fuel System fasteners on the 1967 Chevrolet Corvette. At the pump to block, the fuel pump bolt torques to 30 ft-lbs (3/8" drive, 16 TPI thread).

Transmission — 1967 Chevrolet Corvette

Transmission fasteners on the 1967 Chevrolet Corvette. For the transmission crossmember, plan for a 9/16" tool on a 3/8-16 stud; final torque is 35 ft-lbs (transmission mount bolt). Bellhousing bolt tightens to 55 ft-lbs, takes a 9/16" driver, runs on 7/16-14 threads, located at the bellhousing to block.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1967 Chevrolet Corvette numbers above.

Loading the interactive 1967 Chevrolet Corvette fastener lookup with per-bolt filtering, part links, and torque tools…