1994 Dodge Ram 1500 Lug Nut Torque & Bolt Specs

The 1994 Dodge Ram 1500 lug nut torque is 100 ft-lbs (135 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 1994 Dodge Ram 1500. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 1994 Dodge Ram 1500

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1994 Dodge Ram 1500 owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1994 Dodge Ram 1500?

The OEM-specified lug-nut torque for the 1994 Dodge Ram 1500 is 100 ft-lbs (135 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1994 Dodge Ram 1500 lug nuts?

The 1994 Dodge Ram 1500 uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1994 Dodge Ram 1500 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Dodge Ram 1500 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1994 Dodge Ram 1500 oil drain plug torque & size

→ 1994 Dodge Ram 1500 suspension & steering torque specs (control arm, ball joint, tie rod)

→ 1994 Dodge Ram 1500 axle nut torque spec (CV axle & hub nut)

All 44 1994 Dodge Ram 1500 fastener specs

Per-bolt torque, wrench size, and thread spec for the 1994 Dodge Ram 1500, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 1994 Dodge Ram 1500

Wheel and lug nut spec for the 1994 Dodge Ram 1500. For the all four wheels, plan for a 19mm tool on a M12x1.5 stud; final torque is 100 ft-lbs (135 Nm) (lug nut).

Brakes — 1994 Dodge Ram 1500

Brake fasteners on the 1994 Dodge Ram 1500 — caliper bracket, slide pins, and banjo bolt torque follow. Rear brake caliper slide pins (disc brake — 4th gen) tightens to 32 ft-lbs, takes a See notes driver, located at the rear brake. The front brake caliper bracket bolts uses a See notes drive, torqued to 130 ft-lbs at the front brake. At the rear brake, the rear brake caliper bracket bolts (disc brake — 4th gen) torques to 120 ft-lbs (See notes drive). For the front brake, plan for a See notes tool; final torque is 24 ft-lbs (2009-2014); 31 ft-lbs (2015+) (front brake caliper slide pins). Rear drum brake backing plate bolts — 3rd gen tightens to 48 ft-lbs, takes a See notes driver, located at the rear brake.

Engine — 1994 Dodge Ram 1500

Engine bolt-by-bolt torque for the 1994 Dodge Ram 1500, including the long block, valve covers, and intake. The oil drain plug is a M14x1.5 thread, torqued to 20 ft-lbs (27 Nm) at the oil pan.

Drivetrain — 1994 Dodge Ram 1500

Drivetrain and driveline fasteners for the 1994 Dodge Ram 1500 — axle, transmission, and differential plugs. At the rear differential, the rear pinion nut — 9.25-in torques to 210 ft-lbs minimum (285 Nm) — set to achieve correct preload (See notes drive). For the front driveshaft, plan for a See notes tool; final torque is 85 ft-lbs (front driveshaft bolts (to front diff pinion flange)). Front axle hub nut (4wd — 4th gen ifs) tightens to 185 ft-lbs, takes a See notes driver, located at the front axle. The transfer case mounting nuts (to transmission adapter) uses a See notes drive, torqued to 30–41 ft-lbs (NV241/NV243/NV244/NV273) at the transfer case. At the drivetrain, the transmission crossmember bolts torques to 50 ft-lbs (See notes drive). For the front axle, plan for a See notes tool; final torque is Beginning: 132 ft-lbs | Rotate 5-10 times | Final: 263 ft-lbs (front axle hub nut (4wd — 3rd gen solid axle)). Front differential cover bolts (4wd) — aam 9.25-in ifs tightens to 30 ft-lbs, takes a See notes driver, located at the front differential. The rear driveshaft bolts (to rear diff pinion yoke) uses a See notes drive, torqued to 85 ft-lbs at the rear driveshaft. At the drivetrain, the transmission mount / insulator bolts torques to 50 ft-lbs (See notes drive). For the transfer case, plan for a See notes tool; final torque is 65 ft-lbs (transfer case flange bolts (output yoke)). Rear ring gear bolts — 10.5-in aam tightens to 175 ft-lbs, takes a See notes driver, located at the rear differential. The rear differential cover bolts — 9.25-in aam axle uses a See notes drive, torqued to 30 ft-lbs at the rear differential. At the rear differential, the rear differential cover bolts — 10.5-in aam axle torques to 35 ft-lbs (See notes drive). For the rear differential, plan for a See notes tool; final torque is 65 ft-lbs (Chrysler 9.25"); 103 ft-lbs (AAM 9.25" IFS) (rear ring gear bolts — 9.25-in chrysler/aam).

Suspension — 1994 Dodge Ram 1500

Suspension and chassis fastener torque for the 1994 Dodge Ram 1500 — strut, control arm, and sway bar values. For the wheel, plan for a See notes tool on a M12x1.5 stud; final torque is 100 ft-lbs (135 Nm) (lug nuts). Lower control arm bolts to frame — 3rd gen tightens to 150–210 ft-lbs (varies by specific bolt), takes a See notes driver, located at the front suspension. The upper control arm bolts to frame — 4th gen uses a See notes drive, torqued to 130 ft-lbs at the front suspension. At the steering, the steering shaft pinch bolt torques to 37 ft-lbs (See notes drive). For the front suspension, plan for a See notes tool; final torque is 40 ft-lbs (front shock absorber upper nut — 3rd gen). Lower ball joint nut — 3rd gen (2002-2008) tightens to 60 ft-lbs, takes a See notes driver, located at the front suspension. The upper ball joint nut — 4th gen (2009-2018) uses a See notes drive, torqued to 40 ft-lbs + 200° (TTY sequence) at the front suspension. At the rear suspension, the rear shock absorber (upper and lower) — 3rd gen leaf spring torques to 100 ft-lbs (See notes drive). For the front suspension, plan for a See notes tool; final torque is 37–38 ft-lbs + 90° (lower ball joint nut — 4th gen (2009-2018)). Front sway bar bracket bolts tightens to 45 ft-lbs, takes a See notes driver, located at the front suspension. The upper ball joint nut — 3rd gen (2002-2008) uses a See notes drive, torqued to 60 ft-lbs at the front suspension. At the front suspension, the front shock absorber lower bolt — 3rd gen torques to 100 ft-lbs (See notes drive). For the front suspension, plan for a See notes tool; final torque is 155 ft-lbs (lower control arm bolts to frame — 4th gen). Rear leaf spring front/rear eye bolt nuts — 3rd gen tightens to 170 ft-lbs (standard); 120 ft-lbs (SRT-10), takes a See notes driver, located at the rear suspension. The rear lower control arm bolts — 4th gen coil spring uses a See notes drive, torqued to 200 ft-lbs at the rear suspension. At the front suspension, the upper control arm bolts to frame — 3rd gen torques to 97 ft-lbs (See notes drive). For the rear suspension, plan for a See notes tool; final torque is 110 ft-lbs (rear leaf spring u-bolt nuts — 3rd gen). Rear upper control arm bolts — 4th gen coil spring tightens to 120 ft-lbs, takes a See notes driver, located at the rear suspension. The rear shock absorber (upper and lower) — 4th gen coil spring uses a See notes drive, torqued to 100 ft-lbs at the rear suspension. At the steering, the tie rod end nut (outer) torques to 45 ft-lbs + 90° (See notes drive). For the front suspension, plan for a See notes tool; final torque is Top (bar side): 16–20 ft-lbs; Bottom (control arm side): 75 ft-lbs (front sway bar end link nuts).

Body — 1994 Dodge Ram 1500

Body fasteners on the 1994 Dodge Ram 1500. Cab mount bolts tightens to 40–45 ft-lbs, takes a See notes driver, located at the cab / body. The bed / box mount bolts uses a See notes drive, torqued to 35 ft-lbs at the bed / body.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1994 Dodge Ram 1500 numbers above.

Loading the interactive 1994 Dodge Ram 1500 fastener lookup with per-bolt filtering, part links, and torque tools…