1979 Ford F-150 Lug Nut Torque & Bolt Specs

The 1979 Ford F-150 lug nut torque is 100 ft-lbs (136 Nm), tightened with a 21mm socket on M14 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (136 Nm) · Socket size: 21mm · Thread: M14 x 1.5.

This page is the OEM-referenced fastener summary for the 1979 Ford F-150. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 1979 Ford F-150

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1979 Ford F-150 owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

SAE socket set (1/4"-7/8"), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1979 Ford F-150?

The OEM-specified lug-nut torque for the 1979 Ford F-150 is 100 ft-lbs (136 Nm), using a 21mm socket on M14 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1979 Ford F-150 lug nuts?

The 1979 Ford F-150 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1979 Ford F-150 fasteners metric or SAE?

SAE inch is the standard for this vehicle. Most fasteners on this vehicle are SAE inch, common sizes 1/4", 5/16", 3/8", 7/16", 1/2". Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford F-150 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1979 Ford F-150 lug nut torque: step-by-step & re-torque guide

All 7 1979 Ford F-150 fastener specs

Per-bolt torque, wrench size, and thread spec for the 1979 Ford F-150, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 1979 Ford F-150

Wheel and lug nut spec for the 1979 Ford F-150. At the wheels, the lug nut torques to 100 ft-lbs (136 Nm) (21mm drive, M14 x 1.5 thread). For the wheels, plan for a 21mm tool on a M12x1.5 stud; final torque is 100 ft-lbs (135 Nm) (wheel lug nut).

Brakes — 1979 Ford F-150

Brake fasteners on the 1979 Ford F-150 — caliper bracket, slide pins, and banjo bolt torque follow. For the front wheel hub, plan for a 24mm tool on a M16x2.0 stud; final torque is 185 ft-lbs (250 Nm) (front brake caliper bracket bolt). Brake caliper bolt tightens to 25-30 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the front brake caliper.

Engine — 1979 Ford F-150

Engine bolt-by-bolt torque for the 1979 Ford F-150, including the long block, valve covers, and intake. Oil drain plug tightens to 25-30 ft-lbs, takes a 16mm driver, runs on M14 x 1.5 threads, located at the oil pan.

Drivetrain — 1979 Ford F-150

Drivetrain and driveline fasteners for the 1979 Ford F-150 — axle, transmission, and differential plugs. The differential cover bolt uses a 13mm drive on a M8x1.25 thread, torqued to 25-35 ft-lbs at the differential cover.

Suspension — 1979 Ford F-150

Suspension and chassis fastener torque for the 1979 Ford F-150 — strut, control arm, and sway bar values. At the front wheel hub, the hub assembly bolt torques to 129 ft-lbs (175 Nm) (21mm drive, M14 x 1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1979 Ford F-150 numbers above.

Loading the interactive 1979 Ford F-150 fastener lookup with per-bolt filtering, part links, and torque tools…