2007 Hyundai Tucson Lug Nut Torque & Bolt Specs

The 2007 Hyundai Tucson lug nut torque is 80 ft-lbs, tightened with a 17mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs · Socket size: 17mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2007 Hyundai Tucson. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2007 Hyundai Tucson

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2007 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2007 Hyundai Tucson?

The OEM-specified lug-nut torque for the 2007 Hyundai Tucson is 80 ft-lbs, using a 17mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2007 Hyundai Tucson lug nuts?

The 2007 Hyundai Tucson uses a 17mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2007 Hyundai Tucson fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Hyundai Tucson years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2007 Hyundai Tucson oil drain plug torque & size

→ 2007 Hyundai Tucson suspension & steering torque specs (control arm, ball joint, tie rod)

All 10 2007 Hyundai Tucson fastener specs

Per-bolt torque, wrench size, and thread spec for the 2007 Hyundai Tucson, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2007 Hyundai Tucson

Wheel and lug nut spec for the 2007 Hyundai Tucson. The lug nut uses a 17mm drive on a M12x1.5 thread, torqued to 80 ft-lbs at the all four wheels.

Brakes — 2007 Hyundai Tucson

Brake fasteners on the 2007 Hyundai Tucson — caliper bracket, slide pins, and banjo bolt torque follow. At the front caliper slide pin, the front brake caliper slide pin torques to 16-24 ft-lbs (12mm drive, M10x1.25 thread). For the front brake caliper bracket, plan for a 17mm tool on a M12x1.25 stud; final torque is 58-72 ft-lbs (front brake caliper bracket bolt).

Engine — 2007 Hyundai Tucson

Engine bolt-by-bolt torque for the 2007 Hyundai Tucson, including the long block, valve covers, and intake. For the cylinder head, plan for a 5/8" tool on a M14x1.25 stud; final torque is 15-22 ft-lbs (spark plug). Oil drain plug tightens to 25-33 ft-lbs, takes a 17mm driver, runs on M14x1.5 threads, located at the engine oil pan.

Suspension — 2007 Hyundai Tucson

Suspension and chassis fastener torque for the 2007 Hyundai Tucson — strut, control arm, and sway bar values. Sway bar end link nut tightens to 25-34 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the front/rear sway bar end link. The tie rod end nut uses a 19mm drive on a M14x1.5 thread, torqued to 25-34 ft-lbs at the outer tie rod end to steering knuckle. At the rear shock absorber lower mount, the rear shock lower bolt torques to 65-80 ft-lbs (19mm drive, M14x1.5 thread). For the strut tower top mount, plan for a 17mm tool on a M12x1.25 stud; final torque is 43-58 ft-lbs (front strut top nut). Front hub/bearing nut tightens to 148-192 ft-lbs, takes a 32mm driver, runs on M24x1.5 threads, located at the front wheel hub/axle.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2007 Hyundai Tucson numbers above.

Loading the interactive 2007 Hyundai Tucson fastener lookup with per-bolt filtering, part links, and torque tools…