2022 Kia Stinger Lug Nut Torque & Bolt Specs

The 2022 Kia Stinger lug nut torque is 87 ft-lbs, tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 5x114.3.

Lug nut torque: 87 ft-lbs · Socket size: 21mm · Thread: M12x1.5 · Bolt pattern: 5x114.3.

This page is the OEM-referenced fastener summary for the 2022 Kia Stinger. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2022 Kia Stinger

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Kia Stinger?

The OEM-specified lug-nut torque for the 2022 Kia Stinger is 87 ft-lbs, using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Kia Stinger lug nuts?

The 2022 Kia Stinger uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Kia Stinger fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia Stinger years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Kia Stinger suspension & steering torque specs (control arm, ball joint, tie rod)

All 22 2022 Kia Stinger fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Kia Stinger, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2022 Kia Stinger

Wheel and lug nut spec for the 2022 Kia Stinger. The wheel lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 87 ft-lbs at the wheel hub. At the all four wheels, the lug nut torques to 79-94 ft-lbs (87 ft-lbs target) (21mm drive, M12x1.5 thread).

Brakes — 2022 Kia Stinger

Brake fasteners on the 2022 Kia Stinger — caliper bracket, slide pins, and banjo bolt torque follow. At the caliper slide, the rear caliper slide pin torques to 22 ft-lbs (14mm drive, M10x1.25 thread). For the caliper bracket, plan for a 17mm tool on a M12x1.5 stud; final torque is 65 ft-lbs (rear caliper bracket bolt). Front caliper slide pin tightens to 26 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the caliper slide. The front caliper bracket bolt uses a 19mm drive on a M14x1.5 thread, torqued to 87 ft-lbs at the caliper bracket.

Engine — 2022 Kia Stinger

Engine bolt-by-bolt torque for the 2022 Kia Stinger, including the long block, valve covers, and intake. For the intake manifold, plan for a 12mm tool on a M8x1.25 stud; final torque is 20 ft-lbs (intake manifold bolt). Valve cover bolt tightens to 7 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the valve cover. The oil pan bolt uses a 17mm drive on a M14x1.5 thread, torqued to 29 ft-lbs at the oil pan. At the exhaust manifold, the exhaust manifold stud torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the oil pan, plan for the right driver; final torque is 33 ft-lbs (45 Nm) (oil drain plug). Cylinder head bolt tightens to 23 ft-lbs step2 after 18 ft-lbs step1, takes a 12mm driver, runs on M10x1.25 threads, located at the cylinder head.

Suspension — 2022 Kia Stinger

Suspension and chassis fastener torque for the 2022 Kia Stinger — strut, control arm, and sway bar values. Ball joint nut tightens to 65 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the ball joint. The front control arm bolt uses a 19mm drive on a M14x1.5 thread, torqued to 65 ft-lbs at the control arm. At the knuckle, the tie rod end nut torques to 37 ft-lbs (17mm drive, M12x1.25 thread). For the strut top mount, plan for a 17mm tool on a M12x1.25 stud; final torque is 43 ft-lbs (strut top mount nut). Sway bar link nut tightens to 37 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the sway bar link. The rear control arm bolt uses a 19mm drive on a M14x1.5 thread, torqued to 65 ft-lbs at the control arm.

Body — 2022 Kia Stinger

Body fasteners on the 2022 Kia Stinger. The subframe rear bolt uses a 21mm drive on a M16x1.5 thread, torqued to 95 ft-lbs at the subframe. At the subframe, the subframe front bolt torques to 95 ft-lbs (21mm drive, M16x1.5 thread).

Transmission — 2022 Kia Stinger

Transmission fasteners on the 2022 Kia Stinger. At the transmission mount, the transmission mount bolt torques to 58 ft-lbs (17mm drive, M12x1.5 thread). For the bell housing, plan for a 17mm tool on a M12x1.5 stud; final torque is 58 ft-lbs (bell housing bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Kia Stinger numbers above.

Loading the interactive 2022 Kia Stinger fastener lookup with per-bolt filtering, part links, and torque tools…