2018 Komatsu Pc50mr 2 Bolt Sizes & Torque Specs

Free OEM-referenced torque and bolt specs for the 2018 Komatsu Pc50mr 2.

This page is the OEM-referenced fastener summary for the 2018 Komatsu Pc50mr 2. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2018 Komatsu Pc50mr 2, fasteners follow metric standards typical of late-model Komatsu engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2018 Komatsu Pc50mr 2

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2018 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2018 Komatsu Pc50mr 2?

Manufacturer-specified torque values for the 2018 Komatsu Pc50mr 2 are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Komatsu brand page for the closest model year.

What socket size do I need for the 2018 Komatsu Pc50mr 2 lug nuts?

Most modern Komatsu vehicles use a 19mm or 21mm socket. Older Komatsu models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2018 Komatsu Pc50mr 2 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Komatsu Pc50mr 2 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2018 Komatsu Pc50mr 2 oil drain plug torque & size

All 6 2018 Komatsu Pc50mr 2 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2018 Komatsu Pc50mr 2, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2018 Komatsu Pc50mr 2

Engine bolt-by-bolt torque for the 2018 Komatsu Pc50mr 2, including the long block, valve covers, and intake. For the engine oil sump, plan for a 19mm tool on a M14x1.5 stud; final torque is 29–36 ft-lbs (40–49 Nm) (engine oil drain plug).

Drivetrain — 2018 Komatsu Pc50mr 2

Drivetrain and driveline fasteners for the 2018 Komatsu Pc50mr 2 — axle, transmission, and differential plugs. Final drive drain plug tightens to 35–40 ft-lbs (48–54 Nm), takes a 24mm driver, runs on M18x1.5 threads, located at the final drive gear box (one per side).

Undercarriage — 2018 Komatsu Pc50mr 2

Undercarriage fasteners on the 2018 Komatsu Pc50mr 2. The swing bearing bolt uses a 24mm drive on a M16x2.0 thread, torqued to 155 ft-lbs (210 Nm) at the swing bearing ring (12 bolts). At the track shoes — 3 bolts per shoe, both sides, the track shoe bolt torques to 155 ft-lbs (210 Nm) (24mm drive, M16x1.5 thread).

Attachment — 2018 Komatsu Pc50mr 2

Attachment fasteners on the 2018 Komatsu Pc50mr 2. At the bucket pin lock bolt, the bucket pin retaining bolt torques to 75 ft-lbs (102 Nm) (18mm drive, M12x1.75 thread).

Safety — 2018 Komatsu Pc50mr 2

Safety fasteners on the 2018 Komatsu Pc50mr 2. For the rops to upper frame (4 bolts), plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (210 Nm) (rops mounting bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2018 Komatsu Pc50mr 2 numbers above.

Loading the interactive 2018 Komatsu Pc50mr 2 fastener lookup with per-bolt filtering, part links, and torque tools…