2019 Kubota Bx23s Lug Nut Torque & Bolt Specs

The 2019 Kubota Bx23s lug nut torque is 110-132 ft-lbs (149-179 Nm), tightened with a 21mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 110-132 ft-lbs (149-179 Nm) · Socket size: 21mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2019 Kubota Bx23s. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2019 Kubota Bx23s, fasteners follow metric standards typical of late-model Kubota engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2019 Kubota Bx23s

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2019 Kubota Bx23s?

The OEM-specified lug-nut torque for the 2019 Kubota Bx23s is 110-132 ft-lbs (149-179 Nm), using a 21mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2019 Kubota Bx23s lug nuts?

The 2019 Kubota Bx23s uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2019 Kubota Bx23s fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kubota Bx23s years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2019 Kubota Bx23s oil drain plug torque & size

All 8 2019 Kubota Bx23s fastener specs

Per-bolt torque, wrench size, and thread spec for the 2019 Kubota Bx23s, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 8 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2019 Kubota Bx23s

Wheel and lug nut spec for the 2019 Kubota Bx23s. At the wheels, the wheel lug bolt (front) torques to 110-132 ft-lbs (149-179 Nm) (21mm drive, M14x1.5 thread). OEM-verified spec. For the wheels, plan for a 21mm tool on a M14x1.5 stud; final torque is 80-96 ft-lbs (109-130 Nm) (wheel lug bolt (rear)). Confirmed against manufacturer service literature.

Engine — 2019 Kubota Bx23s

Engine bolt-by-bolt torque for the 2019 Kubota Bx23s, including the long block, valve covers, and intake. For the engine, plan for a 12mm tool on a M10x1.25 stud; final torque is 11-15 ft-lbs (glow plug). Engine oil drain plug tightens to 18-22 ft-lbs, takes a 17mm driver, runs on M14x1.5 threads, located at the engine.

Drivetrain — 2019 Kubota Bx23s

Drivetrain and driveline fasteners for the 2019 Kubota Bx23s — axle, transmission, and differential plugs. Pto shaft retaining nut tightens to 130 ft-lbs (176 Nm), takes a 30mm driver, runs on M20x1.5 threads, located at the mid pto shaft (belly mower engagement).

Attachment — 2019 Kubota Bx23s

Attachment fasteners on the 2019 Kubota Bx23s. The backhoe subframe mounting bolt uses a 24mm drive on a M16x2.0 thread, torqued to 140 ft-lbs at the attachment. At the each spindle on bx2380 belly mower deck, the belly mower blade bolt torques to 55–65 ft-lbs (75–88 Nm) (19mm drive, M12x1.25 thread). For the attachment, plan for a 18mm tool on a M12x1.75 stud; final torque is 65 ft-lbs (loader pivot pin bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 Kubota Bx23s numbers above.

Loading the interactive 2019 Kubota Bx23s fastener lookup with per-bolt filtering, part links, and torque tools…