2017 Kubota L3901 Lug Nut Torque & Bolt Specs

The 2017 Kubota L3901 lug nut torque is 160 ft-lbs (217 Nm), tightened with a 19mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 160 ft-lbs (217 Nm) · Socket size: 19mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2017 Kubota L3901. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2017 Kubota L3901, fasteners follow metric standards typical of late-model Kubota engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2017 Kubota L3901

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2017 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2017 Kubota L3901?

The OEM-specified lug-nut torque for the 2017 Kubota L3901 is 160 ft-lbs (217 Nm), using a 19mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2017 Kubota L3901 lug nuts?

The 2017 Kubota L3901 uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2017 Kubota L3901 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kubota L3901 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 7 2017 Kubota L3901 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2017 Kubota L3901, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 7 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Engine — 2017 Kubota L3901

Engine bolt-by-bolt torque for the 2017 Kubota L3901, including the long block, valve covers, and intake. The engine oil drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 22-25 ft-lbs at the engine. At the engine, the glow plug torques to 11-15 ft-lbs (12mm drive, M10x1.25 thread).

Drivetrain — 2017 Kubota L3901

Drivetrain and driveline fasteners for the 2017 Kubota L3901 — axle, transmission, and differential plugs. At the rear wheel hubs (4 bolts per wheel), the wheel lug bolt (rear) torques to 160 ft-lbs (217 Nm) (19mm drive, M14x1.5 thread). OEM-verified spec. For the front wheel hubs (4 bolts per wheel), plan for a 17mm tool on a M12x1.25 stud; final torque is 100 ft-lbs (136 Nm) (wheel lug bolt (front)). Confirmed against manufacturer service literature. Pto shaft retaining nut tightens to 130 ft-lbs, takes a 30mm driver, runs on M22x1.5 threads, located at the drivetrain.

Suspension — 2017 Kubota L3901

Suspension and chassis fastener torque for the 2017 Kubota L3901 — strut, control arm, and sway bar values. For the suspension, plan for a 36mm tool on a M24x2.0 stud; final torque is 200 ft-lbs (front axle pivot bolt).

Transmission — 2017 Kubota L3901

Transmission fasteners on the 2017 Kubota L3901. Transmission oil drain plug tightens to 25-30 ft-lbs, takes a 27mm driver, runs on M20x1.5 threads, located at the transmission.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2017 Kubota L3901 numbers above.

Loading the interactive 2017 Kubota L3901 fastener lookup with per-bolt filtering, part links, and torque tools…