2001–2009 Lincoln Town Car Lug Nut Torque & Bolt Specs

The 2009 Lincoln Town Car lug nut torque is 95 ft-lbs (129 Nm), tightened with a 19mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 95 ft-lbs (129 Nm) · Socket size: 19mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2009 Lincoln Town Car. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

These specifications also apply to the 2001–2008 model years — identical specs on file for each year.

For the 2009 Lincoln Town Car, fasteners follow metric standards typical of mid-2000s Lincoln engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2009 Lincoln Town Car

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2009 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2009 Lincoln Town Car?

The OEM-specified lug-nut torque for the 2009 Lincoln Town Car is 95 ft-lbs (129 Nm), using a 19mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2009 Lincoln Town Car lug nuts?

The 2009 Lincoln Town Car uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2009 Lincoln Town Car fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Lincoln Town Car years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2009 Lincoln Town Car suspension & steering torque specs (control arm, ball joint, tie rod)

All 25 2009 Lincoln Town Car fastener specs

Per-bolt torque, wrench size, and thread spec for the 2009 Lincoln Town Car, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 22 of the 25 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2009 Lincoln Town Car

Wheel and lug nut spec for the 2009 Lincoln Town Car. plan for a 19mm tool on a M12x1.25 stud; final torque is 95 ft-lbs (129 Nm) (lug nut). Confirmed against manufacturer service literature.

Brakes — 2009 Lincoln Town Car

Brake fasteners on the 2009 Lincoln Town Car — caliper bracket, slide pins, and banjo bolt torque follow. Front brake caliper anchor plate bolt tightens to 118 ft-lbs (160 Nm). This figure is independently verified against OEM service data. The rear brake caliper guide-pin bolt, torqued to 18 ft-lbs (25 Nm). OEM-verified spec. The rear brake caliper anchor plate nut torques to 50 ft-lbs (68 Nm). Confirmed against manufacturer service literature. plan for the right driver; final torque is 27 ft-lbs (36 Nm) (front brake caliper guide-pin bolt). This figure is independently verified against OEM service data.

Engine — 2009 Lincoln Town Car

Engine bolt-by-bolt torque for the 2009 Lincoln Town Car, including the long block, valve covers, and intake. The engine oil drain plug is a M14x1.5 thread, torqued to 17 ft-lbs (23 Nm). The spark plug torques to 13 ft-lbs (18 Nm) (5/8 in drive, 14mm thread).

Drivetrain — 2009 Lincoln Town Car

Drivetrain and driveline fasteners for the 2009 Lincoln Town Car — axle, transmission, and differential plugs. The driveshaft flange bolt torques to 83 ft-lbs (112 Nm).

Suspension — 2009 Lincoln Town Car

Suspension and chassis fastener torque for the 2009 Lincoln Town Car — strut, control arm, and sway bar values. plan for the right driver; final torque is 111 ft-lbs (150 Nm) (rear lower control arm-to-frame). This figure is independently verified against OEM service data. Front upper ball joint nut tightens to 111 ft-lbs (150 Nm). OEM-verified spec. The rear sway bar end-link nut, torqued to 15 ft-lbs (20 Nm). Confirmed against manufacturer service literature. The front upper control arm-to-crossmember torques to 111 ft-lbs (150 Nm). This figure is independently verified against OEM service data. plan for the right driver; final torque is 166 ft-lbs (225 Nm) (front shock lower bolt). OEM-verified spec. Front wheel hub/bearing-to-knuckle bolt tightens to 74 ft-lbs (100 Nm). Confirmed against manufacturer service literature. The front lower control arm-to-crossmember, torqued to 166 ft-lbs (225 Nm). This figure is independently verified against OEM service data. The front lower ball joint nut torques to 111 ft-lbs (150 Nm). OEM-verified spec. plan for the right driver; final torque is 111 ft-lbs (150 Nm) (rear lower control arm-to-axle). Confirmed against manufacturer service literature. Rear upper control arm-to-frame tightens to 111 ft-lbs (150 Nm). This figure is independently verified against OEM service data. The front sway bar end-link nut, torqued to 46 ft-lbs (63 Nm). OEM-verified spec. The rear upper control arm-to-axle torques to 69 ft-lbs (93 Nm). Confirmed against manufacturer service literature. plan for the right driver; final torque is 184 ft-lbs (250 Nm) (watts link center-link-to-diff bolt). This figure is independently verified against OEM service data. Front lower control arm-to-frame tightens to 66 ft-lbs (90 Nm). OEM-verified spec. The rear shock lower bolt (to axle), torqued to 66 ft-lbs (90 Nm). Confirmed against manufacturer service literature.

Steering — 2009 Lincoln Town Car

Steering linkage fasteners on the 2009 Lincoln Town Car. Outer tie rod end nut tightens to 59 ft-lbs (80 Nm). OEM-verified spec. The steering gear-to-crossmember nut, torqued to 76 ft-lbs (103 Nm). Confirmed against manufacturer service literature.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2009 Lincoln Town Car numbers above.

Loading the interactive 2009 Lincoln Town Car fastener lookup with per-bolt filtering, part links, and torque tools…