2017 Mazda CX-9 Lug Nut Torque & Bolt Specs

The 2017 Mazda CX-9 lug nut torque is 90 ft-lbs (122 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 90 ft-lbs (122 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2017 Mazda CX-9. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2017 Mazda CX-9, fasteners follow metric standards typical of late-model Mazda engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2017 Mazda CX-9

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2017 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2017 Mazda CX-9?

The OEM-specified lug-nut torque for the 2017 Mazda CX-9 is 90 ft-lbs (122 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2017 Mazda CX-9 lug nuts?

The 2017 Mazda CX-9 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2017 Mazda CX-9 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Mazda CX-9 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 5 2017 Mazda CX-9 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2017 Mazda CX-9, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2017 Mazda CX-9

Engine bolt-by-bolt torque for the 2017 Mazda CX-9, including the long block, valve covers, and intake. Connecting rod bolt tightens to Stage 1: 18 ft-lbs, Stage 2: +90°, takes a 13mm driver, runs on M9x1.0 threads, located at the engine. The oil drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 25 ft-lbs (34 Nm) at the oil pan. At the engine, the cylinder head bolt torques to Stage 1: 35 ft-lbs, Stage 2: +90°, Stage 3: +90° (14mm drive, M11x1.5 thread).

Drivetrain — 2017 Mazda CX-9

Drivetrain and driveline fasteners for the 2017 Mazda CX-9 — axle, transmission, and differential plugs. The rear differential drain plug uses a 24mm drive on a M18x1.5 thread, torqued to 40 ft-lbs at the rear differential.

Exterior — 2017 Mazda CX-9

Exterior fasteners on the 2017 Mazda CX-9. At the wheel hub, the wheel lug nut torques to 90 ft-lbs (122 Nm) (21mm drive, M12x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2017 Mazda CX-9 numbers above.

Loading the interactive 2017 Mazda CX-9 fastener lookup with per-bolt filtering, part links, and torque tools…