2015 Nissan Rogue Lug Nut Torque & Bolt Specs

The 2015 Nissan Rogue lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2015 Nissan Rogue. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2015 Nissan Rogue

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2015 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2015 Nissan Rogue?

The OEM-specified lug-nut torque for the 2015 Nissan Rogue is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2015 Nissan Rogue lug nuts?

The 2015 Nissan Rogue uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2015 Nissan Rogue fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Rogue years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 4 2015 Nissan Rogue fastener specs

Per-bolt torque, wrench size, and thread spec for the 2015 Nissan Rogue, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 3 of the 4 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2015 Nissan Rogue

Brake fasteners on the 2015 Nissan Rogue — caliper bracket, slide pins, and banjo bolt torque follow. At the front caliper bracket, the front brake caliper bracket bolt torques to 101 ft-lbs (137 Nm). OEM-verified spec. For the front caliper, plan for the right driver; final torque is 25 ft-lbs (34 Nm) (front brake caliper guide pin bolt). Confirmed against manufacturer service literature.

Engine — 2015 Nissan Rogue

Engine bolt-by-bolt torque for the 2015 Nissan Rogue, including the long block, valve covers, and intake. For the oil pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Confirmed against manufacturer service literature.

Wheels & Tires — 2015 Nissan Rogue

Wheels & Tires fasteners on the 2015 Nissan Rogue. Lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.25 threads, located at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2015 Nissan Rogue numbers above.

Loading the interactive 2015 Nissan Rogue fastener lookup with per-bolt filtering, part links, and torque tools…