2004 Pontiac Grand Am Lug Nut Torque & Bolt Specs

The 2004 Pontiac Grand Am lug nut torque is 100 ft-lbs (140 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (140 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2004 Pontiac Grand Am. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2004 Pontiac Grand Am, fasteners follow metric standards typical of mid-2000s Pontiac engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2004 Pontiac Grand Am

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2004 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2004 Pontiac Grand Am?

The OEM-specified lug-nut torque for the 2004 Pontiac Grand Am is 100 ft-lbs (140 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2004 Pontiac Grand Am lug nuts?

The 2004 Pontiac Grand Am uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2004 Pontiac Grand Am fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Pontiac Grand Am years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2004 Pontiac Grand Am suspension & steering torque specs (control arm, ball joint, tie rod)

All 18 2004 Pontiac Grand Am fastener specs

Per-bolt torque, wrench size, and thread spec for the 2004 Pontiac Grand Am, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. All 18 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2004 Pontiac Grand Am

Wheel and lug nut spec for the 2004 Pontiac Grand Am. The lug nut uses a 19mm drive on a M12x1.5 thread, torqued to 100 ft-lbs (140 Nm). This figure is independently verified against OEM service data.

Brakes — 2004 Pontiac Grand Am

Brake fasteners on the 2004 Pontiac Grand Am — caliper bracket, slide pins, and banjo bolt torque follow. The front caliper bracket bolt torques to 85 ft-lbs (115 Nm). OEM-verified spec. plan for the right driver; final torque is 23 ft-lbs (31 Nm) (front brake caliper guide-pin bolt). Confirmed against manufacturer service literature. Rear brake caliper guide-pin bolt tightens to 81 ft-lbs (110 Nm). This figure is independently verified against OEM service data.

Engine — 2004 Pontiac Grand Am

Engine bolt-by-bolt torque for the 2004 Pontiac Grand Am, including the long block, valve covers, and intake. plan for the right driver; final torque is 18 ft-lbs (25 Nm) (engine oil drain plug (2.2l)). Confirmed against manufacturer service literature. Engine oil drain plug (3.4l) tightens to 18 ft-lbs (25 Nm). This figure is independently verified against OEM service data. The spark plug (2.2l), torqued to 15 ft-lbs (20 Nm). OEM-verified spec. The spark plug (3.4l) torques to 11 ft-lbs (15 Nm). Confirmed against manufacturer service literature.

Drivetrain — 2004 Pontiac Grand Am

Drivetrain and driveline fasteners for the 2004 Pontiac Grand Am — axle, transmission, and differential plugs. Front hub/axle nut tightens to 173 ft-lbs (235 Nm) new-style / 284 ft-lbs (385 Nm) old-style. This figure is independently verified against OEM service data.

Suspension — 2004 Pontiac Grand Am

Suspension and chassis fastener torque for the 2004 Pontiac Grand Am — strut, control arm, and sway bar values. The front strut mount-to-body nuts, torqued to 18 ft-lbs (25 Nm). OEM-verified spec. The front strut-to-knuckle nuts torques to 133 ft-lbs (180 Nm). Confirmed against manufacturer service literature. plan for the right driver; final torque is 89 ft-lbs (120 Nm) (rear strut-to-knuckle nut). This figure is independently verified against OEM service data. Rear trailing arm-to-body bolt tightens to 48 ft-lbs (65 Nm) + 120 deg. OEM-verified spec. The lower ball joint-to-knuckle nut, torqued to 89 lb-in (10 Nm) + 180 deg. Confirmed against manufacturer service literature. The front stabilizer bar link nut torques to 13 ft-lbs (17 Nm). This figure is independently verified against OEM service data. plan for the right driver; final torque is 70 ft-lbs (95 Nm) (front wheel hub/bearing-to-knuckle bolts). OEM-verified spec. Lower control arm-to-frame bolt (rear bushing) tightens to 74 ft-lbs (100 Nm) + 180 deg. Confirmed against manufacturer service literature.

Steering — 2004 Pontiac Grand Am

Steering linkage fasteners on the 2004 Pontiac Grand Am. The outer tie rod end nut torques to 15 ft-lbs (20 Nm) + 180 deg. Confirmed against manufacturer service literature.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2004 Pontiac Grand Am numbers above.

Loading the interactive 2004 Pontiac Grand Am fastener lookup with per-bolt filtering, part links, and torque tools…