2026 Ram Ram 3500 Lug Nut Torque & Bolt Specs

The 2026 Ram Ram 3500 lug nut torque is 129 ft-lbs (175 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 129 ft-lbs (175 Nm) · Socket size: 22mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2026 Ram Ram 3500. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 2026 Ram Ram 3500

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2026 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2026 Ram Ram 3500?

The OEM-specified lug-nut torque for the 2026 Ram Ram 3500 is 129 ft-lbs (175 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2026 Ram Ram 3500 lug nuts?

The 2026 Ram Ram 3500 uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2026 Ram Ram 3500 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ram Ram 3500 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 14 2026 Ram Ram 3500 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2026 Ram Ram 3500, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2026 Ram Ram 3500

Wheel and lug nut spec for the 2026 Ram Ram 3500. For the rear inner wheel, plan for a 22mm tool on a M14x1.5 stud; final torque is 129 ft-lbs (175 Nm) (inner rear lug nut (drw)). Lug nut tightens to 130 ft-lbs (176 Nm), takes a 22mm driver, runs on M14x1.5 threads, located at the all four corners. The outer rear lug nut (drw) uses a 22mm drive on a M14x1.5 thread, torqued to 129 ft-lbs (175 Nm) at the rear outer wheel.

Brakes — 2026 Ram Ram 3500

Brake fasteners on the 2026 Ram Ram 3500 — caliper bracket, slide pins, and banjo bolt torque follow. Front brake caliper bracket bolt tightens to 125 ft-lbs, takes a 18mm driver, runs on M14x2.0 threads, located at the front axle, caliper bracket. The front caliper slide pin uses a 13mm drive on a M10x1.5 thread, torqued to 25-35 ft-lbs at the front caliper.

Engine — 2026 Ram Ram 3500

Engine bolt-by-bolt torque for the 2026 Ram Ram 3500, including the long block, valve covers, and intake. The glow plug uses a 12mm drive on a M12x1.25 thread, torqued to 15 ft-lbs at the cylinder head. At the cylinder head, the spark plug torques to 20-30 ft-lbs (9/16" drive, M14x1.25 thread). For the oil pan, plan for a 27mm tool on a M18x1.5 stud; final torque is 37 ft-lbs (50 Nm) (oil drain plug).

Drivetrain — 2026 Ram Ram 3500

Drivetrain and driveline fasteners for the 2026 Ram Ram 3500 — axle, transmission, and differential plugs. At the transfer case, the transfer case drain plug torques to 20-25 ft-lbs (24mm drive, M20x1.5 thread). For the front differential, plan for a See notes tool on a 3/8" sq stud; final torque is 25 ft-lbs (front differential fill plug).

Suspension — 2026 Ram Ram 3500

Suspension and chassis fastener torque for the 2026 Ram Ram 3500 — strut, control arm, and sway bar values. For the rear leaf spring, plan for a 22mm tool on a M14x2.0 stud; final torque is 135-175 ft-lbs (rear leaf spring u-bolt nut).

Steering — 2026 Ram Ram 3500

Steering linkage fasteners on the 2026 Ram Ram 3500. Tie rod end nut tightens to 60-75 ft-lbs, takes a 22mm driver, runs on M14x1.5 threads, located at the tie rod end.

Transmission — 2026 Ram Ram 3500

Transmission fasteners on the 2026 Ram Ram 3500. The transmission pan bolt uses a 8mm drive on a M8x1.25 thread, torqued to 14 ft-lbs at the transmission pan.

Axle / Drivetrain — 2026 Ram Ram 3500

Axle / Drivetrain fasteners on the 2026 Ram Ram 3500. At the front wheel hub, the front axle hub nut (4wd) torques to 132 ft-lbs initial (rotate hub 5-10x to seat bearing), then 263 ft-lbs final (See notes drive, M34x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2026 Ram Ram 3500 numbers above.

Loading the interactive 2026 Ram Ram 3500 fastener lookup with per-bolt filtering, part links, and torque tools…