2007 Toyota Avalon Lug Nut Torque & Bolt Specs

The 2007 Toyota Avalon lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2007 Toyota Avalon. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2007 Toyota Avalon

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2007 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2007 Toyota Avalon?

The OEM-specified lug-nut torque for the 2007 Toyota Avalon is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2007 Toyota Avalon lug nuts?

The 2007 Toyota Avalon uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2007 Toyota Avalon fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Avalon years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2007 Toyota Avalon oil drain plug torque & size

→ 2007 Toyota Avalon suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2007 Toyota Avalon fastener specs

Per-bolt torque, wrench size, and thread spec for the 2007 Toyota Avalon, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 20 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2007 Toyota Avalon

Wheel and lug nut spec for the 2007 Toyota Avalon. Wheel lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.5 threads, located at the wheel hub.

Brakes — 2007 Toyota Avalon

Brake fasteners on the 2007 Toyota Avalon — caliper bracket, slide pins, and banjo bolt torque follow. The rear caliper slide pin uses a 12mm hex drive on a M10 thread, torqued to 32 ft-lb at the rear caliper. At the steering knuckle, the brake caliper bracket bolt torques to 85 ft-lbs (17mm drive, M12x1.25 thread). For the rear knuckle, plan for a 14mm hex tool on a M12 stud; final torque is 46 ft-lb (rear caliper bracket bolt). Front caliper bracket bolt tightens to 79 ft-lb, takes a 17mm hex driver, runs on M14 threads, located at the front knuckle. The front caliper slide pin uses a 12mm hex drive on a M10 thread, torqued to 25 ft-lb at the front caliper. At the caliper bracket, the brake caliper bolt torques to 55 ft-lbs (14mm drive, M12x1.25 thread).

Engine — 2007 Toyota Avalon

Engine bolt-by-bolt torque for the 2007 Toyota Avalon, including the long block, valve covers, and intake. At the engine, the cylinder head bolt torques to Step 1: 36 N·m (367 kgf·cm, 27 ft-lb) | Step 2: +90° | Step 3: +90° — Bank 2 also takes 2 extra bolts at a single stage of 30 N·m (22 ft-lb) (14mm drive). Confirmed against manufacturer service literature. For the cylinder head, plan for a 5/8" (16mm) tool on a M14x1.25 stud; final torque is 13 ft-lb (spark plug). Valve cover bolt tightens to 8 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the cylinder head. The connecting rod bolt uses a 13mm drive, torqued to Step 1: 25 N·m (255 kgf·cm, 18 ft-lb) | Step 2: +90° at the engine. Confirmed against manufacturer service literature. At the engine block, the oil filter housing cap torques to 25 ft-lbs (64mm drive, M64x1.5 thread). For the engine oil pan, plan for a 14mm hex tool on a M12x1.25 stud; final torque is 30 ft-lbs (40 Nm) (oil drain plug).

Drivetrain — 2007 Toyota Avalon

Drivetrain and driveline fasteners for the 2007 Toyota Avalon — axle, transmission, and differential plugs. For the front hub, plan for a 32mm hex tool on a M24x1.5 stud; final torque is 217 ft-lb (front axle hub nut).

Suspension — 2007 Toyota Avalon

Suspension and chassis fastener torque for the 2007 Toyota Avalon — strut, control arm, and sway bar values. Front stabilizer link tightens to 44 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the strut. The steering knuckle bolt uses a 19mm drive on a M14x1.5 thread, torqued to 85 ft-lbs at the lower control arm. At the lower control arm, the lower ball joint nut torques to 85 ft-lbs (19mm drive, M14x1.5 thread).

Transmission — 2007 Toyota Avalon

Transmission fasteners on the 2007 Toyota Avalon. The transmission pan bolt uses a 10mm drive on a M6x1.0 thread, torqued to 7 ft-lbs at the transmission pan. At the transmission pan, the transmission drain plug torques to 29 ft-lbs (24mm drive, M20x1.5 thread).

Wheel Hardware — 2007 Toyota Avalon

Wheel Hardware fasteners on the 2007 Toyota Avalon. At the all wheels, the lug nut torques to 80 ft-lbs (108 Nm) (21mm hex drive, M12x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2007 Toyota Avalon numbers above.

Loading the interactive 2007 Toyota Avalon fastener lookup with per-bolt filtering, part links, and torque tools…