1987 Toyota Camry Lug Nut Torque & Bolt Specs

The 1987 Toyota Camry lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 1987 Toyota Camry. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 1987 Toyota Camry

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1987 Toyota Camry owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1987 Toyota Camry?

The OEM-specified lug-nut torque for the 1987 Toyota Camry is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1987 Toyota Camry lug nuts?

The 1987 Toyota Camry uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1987 Toyota Camry fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Camry years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1987 Toyota Camry oil drain plug torque & size

→ 1987 Toyota Camry suspension & steering torque specs (control arm, ball joint, tie rod)

All 14 1987 Toyota Camry fastener specs

Per-bolt torque, wrench size, and thread spec for the 1987 Toyota Camry, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 1987 Toyota Camry

Brake fasteners on the 1987 Toyota Camry — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper bolt uses a 14mm drive on a M12x1.25 thread, torqued to 65 ft-lbs at the caliper to steering knuckle. At the face of brake drum, the brake drum retaining screw torques to Hand Tight (#3 Phillips drive, M6x1.0 thread).

Engine — 1987 Toyota Camry

Engine bolt-by-bolt torque for the 1987 Toyota Camry, including the long block, valve covers, and intake. At the oil pan, the oil drain plug torques to 30 ft-lbs (40 Nm) (14mm drive, M12x1.25 thread). For the exhaust to cylinder head, plan for a 12mm tool on a M8x1.25 stud; final torque is 25 ft-lbs (exhaust manifold nut). Intake manifold nut tightens to 14 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the intake to cylinder head. The cylinder head bolt uses a 14mm drive on a M10x1.25 thread, torqued to 44 ft-lbs at the cylinder head to block. At the engine, the connecting rod bolt (13mm drive). For the top of cylinder head, plan for a 12mm tool on a M8x1.25 stud; final torque is 14 ft-lbs (valve cover nut).

Drivetrain — 1987 Toyota Camry

Drivetrain and driveline fasteners for the 1987 Toyota Camry — axle, transmission, and differential plugs. For the center of hub, plan for a 30mm tool on a M22x1.5 stud; final torque is 137 ft-lbs (axle nut).

Suspension — 1987 Toyota Camry

Suspension and chassis fastener torque for the 1987 Toyota Camry — strut, control arm, and sway bar values. Front strut top nut tightens to 29 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the top of strut tower. The wheel lug nut uses a 19mm drive on a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm) at the wheels. At the control arm to knuckle, the lower ball joint bolt torques to 58 ft-lbs (17mm drive, M12x1.25 thread).

Body — 1987 Toyota Camry

Body fasteners on the 1987 Toyota Camry. The fender bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the engine bay & door jamb.

Wheels & Tires — 1987 Toyota Camry

Wheels & Tires fasteners on the 1987 Toyota Camry. At the wheel hub, the lug nut torques to 80 ft-lbs (108 Nm) (21mm drive, M12x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1987 Toyota Camry numbers above.

Loading the interactive 1987 Toyota Camry fastener lookup with per-bolt filtering, part links, and torque tools…