2013 Toyota Camry Lug Nut Torque & Bolt Specs

The 2013 Toyota Camry lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2013 Toyota Camry. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Seventh generation (XV50, 2012–2017)

The 2013 Camry is Toyota's XV50-generation sedan (2012–2017), offered with a 178-hp 2.5-liter four-cylinder, an optional 268-hp 3.5-liter V6, or a 2.5-liter hybrid making about 200 hp combined.

Wheels use a five-lug pattern on M12x1.5 studs. All three drivetrains are aluminum-block engines, so cover and accessory fasteners thread into soft alloy and rely on modest, accurate torque.

Common fastener categories on the 2013 Toyota Camry

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2013 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2013 Toyota Camry?

The OEM-specified lug-nut torque for the 2013 Toyota Camry is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2013 Toyota Camry lug nuts?

The 2013 Toyota Camry uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2013 Toyota Camry fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Camry years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2013 Toyota Camry oil drain plug torque & size

→ Full 2013 Toyota Camry maintenance schedule (intervals, costs & free tracker) on ServiceSageAuto

All 9 2013 Toyota Camry fastener specs

Per-bolt torque, wrench size, and thread spec for the 2013 Toyota Camry, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 3 of the 9 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2013 Toyota Camry

Wheel and lug nut spec for the 2013 Toyota Camry. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (21mm drive, M12x1.5 thread).

Brakes — 2013 Toyota Camry

Brake fasteners on the 2013 Toyota Camry — caliper bracket, slide pins, and banjo bolt torque follow. For the caliper bracket, plan for a 12mm tool on a M8x1.25 stud; final torque is 22 ft-lbs (brake caliper pin). Brake line banjo bolt tightens to 25 ft-lbs, takes a 10mm driver, runs on M10x1.0 threads, located at the caliper.

Engine — 2013 Toyota Camry

Engine bolt-by-bolt torque for the 2013 Toyota Camry, including the long block, valve covers, and intake. Oil filter housing bolt tightens to 10 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the engine block. The oil drain plug is a M12x1.25 thread, torqued to 30 ft-lbs (40 Nm) at the oil pan. OEM-verified spec. At the engine, the cylinder head bolt torques to Step 1: 36 N·m (367 kgf·cm, 27 ft-lb) | Step 2: +90° | Step 3: +90° — Bank 2 also takes 2 extra bolts at a single stage of 30 N·m (22 ft-lb) (14mm drive). Confirmed against manufacturer service literature. For the engine, plan for a 13mm tool; final torque is Step 1: 25 N·m (255 kgf·cm, 18 ft-lb) | Step 2: +90° (connecting rod bolt). This figure is independently verified against OEM service data. Timing cover bolt tightens to 10 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the front of engine.

Suspension — 2013 Toyota Camry

Suspension and chassis fastener torque for the 2013 Toyota Camry — strut, control arm, and sway bar values. The sway bar link nut uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the sway bar.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2013 Toyota Camry numbers above.

Loading the interactive 2013 Toyota Camry fastener lookup with per-bolt filtering, part links, and torque tools…