2018 Toyota Camry Lug Nut Torque & Bolt Specs

The 2018 Toyota Camry lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2018 Toyota Camry. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Eighth generation (XV70, 2018–2024)

The 2018 Camry is the XV70-generation sedan (2018–2024), the first Camry on Toyota's TNGA-K platform, with a 203-hp 2.5-liter four-cylinder, a 301-hp 3.5-liter V6, or a 2.5-liter hybrid near 208 hp combined.

The XV70 keeps the five-lug, M12x1.5 wheel convention. Its TNGA-K architecture relocated the hybrid battery under the rear seat rather than the trunk, lowering the car's center of gravity.

Common fastener categories on the 2018 Toyota Camry

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2018 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2018 Toyota Camry?

The OEM-specified lug-nut torque for the 2018 Toyota Camry is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2018 Toyota Camry lug nuts?

The 2018 Toyota Camry uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2018 Toyota Camry fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Camry years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2018 Toyota Camry oil drain plug torque & size

→ 2018 Toyota Camry suspension & steering torque specs (control arm, ball joint, tie rod)

→ Full 2018 Toyota Camry maintenance schedule (intervals, costs & free tracker) on ServiceSageAuto

All 21 2018 Toyota Camry fastener specs

Per-bolt torque, wrench size, and thread spec for the 2018 Toyota Camry, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 14 of the 21 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2018 Toyota Camry

Wheel and lug nut spec for the 2018 Toyota Camry. The wheel lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm) at the wheel hub.

Brakes — 2018 Toyota Camry

Brake fasteners on the 2018 Toyota Camry — caliper bracket, slide pins, and banjo bolt torque follow. At the front, the front caliper guide pin torques to 25 ft-lbs (34 Nm). OEM-verified spec. For the steering knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 79 ft-lbs (107 Nm) (caliper bracket bolt). Confirmed against manufacturer service literature.

Engine — 2018 Toyota Camry

Engine bolt-by-bolt torque for the 2018 Toyota Camry, including the long block, valve covers, and intake. plan for a 17mm tool on a M12x1.25 stud; final torque is 59 ft-lbs (80 Nm) (engine mount bracket bolt). Confirmed against manufacturer service literature. Valve cover bolt tightens to 8 ft-lbs (10.8 Nm), takes a 10mm driver, runs on M6x1.0 threads. This figure is independently verified against OEM service data. The crankshaft balancer (damper) bolt uses a 22mm drive on a M14x1.5 thread, torqued to 192 ft-lbs (260 Nm). OEM-verified spec. The oil drain plug torques to 30 ft-lbs (40 Nm) (14mm drive, M12x1.25 thread). Confirmed against manufacturer service literature. For the engine, plan for a 14mm tool (cylinder head bolt). Connecting rod bolt takes a 13mm driver, located at the engine.

Suspension — 2018 Toyota Camry

Suspension and chassis fastener torque for the 2018 Toyota Camry — strut, control arm, and sway bar values. Front strut lower bolt tightens to 155 ft-lbs (210 Nm), takes a 22mm driver, runs on M14x1.5 threads. This figure is independently verified against OEM service data. The front strut upper mount nut uses a 17mm drive on a M12x1.25 thread, torqued to 59 ft-lbs (80 Nm). OEM-verified spec. At the sway bar, the sway bar link nut torques to 43 ft-lbs (17mm drive, M12x1.25 thread). plan for a 19mm tool on a M14x1.5 stud; final torque is 150 ft-lbs (203 Nm) (lower control arm to frame bolt). This figure is independently verified against OEM service data. Sway bar end link nut tightens to 55 ft-lbs (75 Nm), takes a 17mm driver, runs on M12x1.5 threads. OEM-verified spec.

Cooling — 2018 Toyota Camry

Cooling fasteners on the 2018 Toyota Camry. The water pump bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs (20 Nm). OEM-verified spec.

Ignition — 2018 Toyota Camry

Ignition fasteners on the 2018 Toyota Camry. The ignition coil bolt torques to 89 in-lbs (10 Nm) (10mm drive, M6x1.0 thread). Confirmed against manufacturer service literature. plan for a 14mm tool on a M12x1.25 stud; final torque is 13 ft-lbs (18 Nm) (spark plug). This figure is independently verified against OEM service data.

Driveline — 2018 Toyota Camry

Driveline fasteners on the 2018 Toyota Camry. plan for a 30mm tool on a M22x1.5 stud; final torque is 217 ft-lbs (294 Nm) (axle nut). This figure is independently verified against OEM service data.

Interior — 2018 Toyota Camry

Interior fasteners on the 2018 Toyota Camry. Front seat mount bolt tightens to 37 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the floor pan. The seat belt anchor bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the b-pillar. At the floor pan, the center console bolt torques to 7 ft-lbs (10mm drive, M6x1.0 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2018 Toyota Camry numbers above.

Loading the interactive 2018 Toyota Camry fastener lookup with per-bolt filtering, part links, and torque tools…