2022 Toyota Camry Lug Nut Torque & Bolt Specs

The 2022 Toyota Camry lug nut torque is 103 Nm (76 ft-lbs), tightened with a 21mm socket on M12 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 103 Nm (76 ft-lbs) · Socket size: 21mm · Thread: M12 x 1.5.

This page is the OEM-referenced fastener summary for the 2022 Toyota Camry. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2022 Toyota Camry

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Toyota Camry?

The OEM-specified lug-nut torque for the 2022 Toyota Camry is 103 Nm (76 ft-lbs), using a 21mm socket on M12 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Toyota Camry lug nuts?

The 2022 Toyota Camry uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Toyota Camry fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Camry years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Toyota Camry oil drain plug torque & size

→ 2022 Toyota Camry suspension & steering torque specs (control arm, ball joint, tie rod)

All 22 2022 Toyota Camry fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Toyota Camry, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 12 of the 22 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2022 Toyota Camry

Wheel and lug nut spec for the 2022 Toyota Camry. At the wheel hub, the wheel lug nut torques to 103 Nm (76 ft-lbs) (21mm drive, M12 x 1.5 thread).

Brakes — 2022 Toyota Camry

Brake fasteners on the 2022 Toyota Camry — caliper bracket, slide pins, and banjo bolt torque follow. For the caliper bracket, plan for a 12mm tool on a M8x1.25 stud; final torque is 22 ft-lbs (brake caliper pin).

Engine — 2022 Toyota Camry

Engine bolt-by-bolt torque for the 2022 Toyota Camry, including the long block, valve covers, and intake. Alternator bolt tightens to 33 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the front of engine. The valve cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs (10.8 Nm). OEM-verified spec. The crankshaft balancer (damper) bolt torques to 192 ft-lbs (260 Nm) (22mm drive, M14x1.5 thread). Confirmed against manufacturer service literature. For the engine block, plan for a 10mm tool on a M6x1.0 stud; final torque is 10 ft-lbs (oil filter housing bolt). Connecting rod bolt tightens to Stage 1: 18 ft-lbs, Stage 2: +45°, takes a 13mm driver, runs on M9x1.0 threads, located at the engine. The engine mount bracket bolt uses a 17mm drive on a M12x1.25 thread, torqued to 59 ft-lbs (80 Nm). Confirmed against manufacturer service literature. The oil drain plug torques to 30 ft-lbs (40 Nm) (14mm drive, M12x1.25 thread). This figure is independently verified against OEM service data. For the front of engine, plan for a 10mm tool on a M6x1.0 stud; final torque is 10 ft-lbs (timing cover bolt). Cylinder head bolt tightens to Stage 1: 40 ft-lbs, Stage 2: +90°, takes a 14mm driver, runs on M10x1.5 threads, located at the engine.

Suspension — 2022 Toyota Camry

Suspension and chassis fastener torque for the 2022 Toyota Camry — strut, control arm, and sway bar values. The lower control arm to frame bolt uses a 19mm drive on a M14x1.5 thread, torqued to 150 ft-lbs (203 Nm). OEM-verified spec. The front strut lower bolt torques to 155 ft-lbs (210 Nm) (22mm drive, M14x1.5 thread). Confirmed against manufacturer service literature. plan for a 17mm tool on a M12x1.25 stud; final torque is 59 ft-lbs (80 Nm) (front strut upper mount nut). This figure is independently verified against OEM service data. Ball joint nut tightens to 67 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the control arm. The sway bar end link nut uses a 17mm drive on a M12x1.5 thread, torqued to 55 ft-lbs (75 Nm). Confirmed against manufacturer service literature.

Ignition — 2022 Toyota Camry

Ignition fasteners on the 2022 Toyota Camry. The ignition coil bolt torques to 89 in-lbs (10 Nm) (10mm drive, M6x1.0 thread). Confirmed against manufacturer service literature. plan for a 14mm tool on a M12x1.25 stud; final torque is 13 ft-lbs (18 Nm) (spark plug). This figure is independently verified against OEM service data.

Driveline — 2022 Toyota Camry

Driveline fasteners on the 2022 Toyota Camry. plan for a 30mm tool on a M22x1.5 stud; final torque is 217 ft-lbs (294 Nm) (axle nut). This figure is independently verified against OEM service data.

Cooling — 2022 Toyota Camry

Cooling fasteners on the 2022 Toyota Camry. Water pump bolt tightens to 15 ft-lbs (20 Nm), takes a 12mm driver, runs on M8x1.25 threads. OEM-verified spec.

Interior — 2022 Toyota Camry

Interior fasteners on the 2022 Toyota Camry. The center console bolt uses a 10mm drive on a M6x1.0 thread, torqued to 7 ft-lbs at the floor pan. At the door frame, the door hinge bolt torques to 27 ft-lbs (12mm drive, M8x1.25 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Toyota Camry numbers above.

Loading the interactive 2022 Toyota Camry fastener lookup with per-bolt filtering, part links, and torque tools…