2010 Toyota RAV4 Brake Job Torque Specs

Compare 9 named brake fastener records for 2010 Toyota RAV4. These records are not a universal caliper mounting or bracket torque answer. Verify the exact part, axle, variant and source against the service manual. Full bolt records for the rest of the vehicle are linked below.

Caliper Bracket Bolts records — 2010 Toyota RAV4

Recorded fastener names and fields for 2010 Toyota RAV4: Front Brake Caliper Bracket Bolt (to Knuckle) (torques to 98 Nm (72 ft-lbs), 17mm socket, M12x1.25 thread); Rear Brake Caliper Bracket Bolt (to Carrier) (torques to 88 Nm (65 ft-lbs), 17mm socket, M12x1.25 thread). Grouping is navigation, not verification of a part's type, source or applicability. Confirm the exact fastener, axle, variant and procedure in the service manual; never substitute a slide-pin or bleeder specification for a mounting or bracket bolt.

Caliper Slide / Guide Pins records — 2010 Toyota RAV4

Recorded fastener names and fields for 2010 Toyota RAV4: Rear Brake Caliper Slide Pin Bolt (torques to 27 Nm (20 ft-lbs), 14mm (bolt) / 14mm (pin hold) socket, M8x1.25 thread); Front Brake Caliper Slide Pin Bolt (torques to 34 Nm (25 ft-lbs), 14mm (with 14mm hold on slide pin) socket, M10x1.25 thread). Grouping is navigation, not verification of a part's type, source or applicability. Confirm the exact fastener, axle, variant and procedure in the service manual; never substitute a slide-pin or bleeder specification for a mounting or bracket bolt.

Hydraulic (Banjo & Bleeder) records — 2010 Toyota RAV4

Recorded fastener names and fields for 2010 Toyota RAV4: Brake Line Union Nut (torques to 15 Nm (11 ft-lbs), 10mm Flare Nut Wrench socket, M10x1.0 thread); Front Brake Hose Banjo Bolt (torques to 29 Nm (22 ft-lbs), 14mm (banjo) socket, M10x1.0 thread); Rear Brake Hose Banjo Bolt (torques to 30 Nm (22 ft-lbs), 14mm (banjo) socket, M10x1.0 thread); Bleeder Screw (Front and Rear) (torques to 8.3 Nm (73 in-lbs), 8mm socket, M8x1.25 thread). Grouping is navigation, not verification of a part's type, source or applicability. Confirm the exact fastener, axle, variant and procedure in the service manual; never substitute a slide-pin or bleeder specification for a mounting or bracket bolt.

Other Brake Fasteners records — 2010 Toyota RAV4

Recorded fastener names and fields for 2010 Toyota RAV4: Brake Master Cylinder Nut (torques to 13 Nm (9 ft-lbs), 12mm socket, M10x1.25 thread). Grouping is navigation, not verification of a part's type, source or applicability. Confirm the exact fastener, axle, variant and procedure in the service manual; never substitute a slide-pin or bleeder specification for a mounting or bracket bolt.

How to do a RAV4 brake job right

Consult the service manual for the exact axle and variant before starting. Identify the mounting bolts, bracket bolts and slide/guide pins separately. Bolt reuse, lubrication, threadlocker and torque-to-yield requirements are application-specific, not universal rules for a display group. Support the caliper safely without loading the hose, and use the specified tightening sequence with a calibrated torque wrench rather than an impact tool.

Tools you need for a RAV4 brake job

Recorded socket sizes for 2010 Toyota RAV4: 12mm, 10mm Flare Nut Wrench, 14mm (banjo), 14mm (bolt) / 14mm (pin hold), 17mm, 14mm (with 14mm hold on slide pin). Other tools may include a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the specified torque values, plus thread-locker or brake lubricant only where the manual calls for it. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…