2018 BMW 5 Series Lug Nut Torque & Bolt Specs

The 2018 BMW 5 Series lug nut torque is 103 ft-lbs (140 Nm), tightened with a 17mm socket on M14x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 103 ft-lbs (140 Nm) · Socket size: 17mm · Thread: M14x1.25.

This page is the OEM-referenced fastener summary for the 2018 BMW 5 Series. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2018 BMW 5 Series, fasteners follow metric standards typical of late-model BMW engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2018 BMW 5 Series

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2018 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2018 BMW 5 Series?

The OEM-specified lug-nut torque for the 2018 BMW 5 Series is 103 ft-lbs (140 Nm), using a 17mm socket on M14x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2018 BMW 5 Series lug nuts?

The 2018 BMW 5 Series uses a 17mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2018 BMW 5 Series fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other BMW 5 Series years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 5 2018 BMW 5 Series fastener specs

Per-bolt torque, wrench size, and thread spec for the 2018 BMW 5 Series, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2018 BMW 5 Series

Wheel and lug nut spec for the 2018 BMW 5 Series. The wheel lug nut torques to 103 ft-lbs (140 Nm) (17mm drive, M14x1.25 thread).

Brakes — 2018 BMW 5 Series

Brake fasteners on the 2018 BMW 5 Series — caliper bracket, slide pins, and banjo bolt torque follow. For the front brakes, plan for a E16 external Torx tool on a M12 stud; final torque is 96 ft-lbs (front brake caliper bracket bolt). Front brake caliper slide pin tightens to 26 ft-lbs, takes a 7mm Allen driver, runs on M8 threads, located at the front brakes.

Engine — 2018 BMW 5 Series

Engine bolt-by-bolt torque for the 2018 BMW 5 Series, including the long block, valve covers, and intake. Oil drain plug tightens to 19 ft-lbs, takes a 17mm hex driver, runs on M12x1.5 threads, located at the engine.

Wheel — 2018 BMW 5 Series

Wheel fasteners on the 2018 BMW 5 Series. The wheel bolt uses a 17mm hex drive on a M14x1.25 thread, torqued to 103 ft-lbs at the wheel.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2018 BMW 5 Series numbers above.

Loading the interactive 2018 BMW 5 Series fastener lookup with per-bolt filtering, part links, and torque tools…