1999 Chevrolet Blazer Lug Nut Torque & Bolt Specs

The 1999 Chevrolet Blazer lug nut torque is 100 ft-lbs (136 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (136 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 1999 Chevrolet Blazer. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

GM lug-nut torque clusters around 140 ft-lbs (190 Nm) for half-ton Silverado/Sierra and 100 ft-lbs for passenger cars like Malibu, Impala, and Cruze. GM heavy-duty trucks (2500HD/3500HD) jump to 165 ft-lbs. Most GM passenger cars use a 19mm socket; trucks moved from 22mm to 22mm-with-deep-well in 2014. Watch for GM's flat-flange lug nut design on the Silverado — the standard cone-seat aftermarket lugs will not seat correctly.

Common fastener categories on the 1999 Chevrolet Blazer

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1999 Chevrolet Blazer owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1999 Chevrolet Blazer?

The OEM-specified lug-nut torque for the 1999 Chevrolet Blazer is 100 ft-lbs (136 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1999 Chevrolet Blazer lug nuts?

The 1999 Chevrolet Blazer uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1999 Chevrolet Blazer fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Chevrolet Blazer years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1999 Chevrolet Blazer suspension & steering torque specs (control arm, ball joint, tie rod)

All 35 1999 Chevrolet Blazer fastener specs

Per-bolt torque, wrench size, and thread spec for the 1999 Chevrolet Blazer, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 1999 Chevrolet Blazer

Brake fasteners on the 1999 Chevrolet Blazer — caliper bracket, slide pins, and banjo bolt torque follow. Rear caliper bracket bolt tightens to 23 ft-lbs (31 Nm), takes a 10mm hex driver, runs on M8x1.25 threads. The front caliper slide pin bolt uses a 13mm drive on a M10x1.5 thread, torqued to 38 ft-lbs (51 Nm) at the front. At the front, the front caliper bracket bolt torques to 81 ft-lbs (110 Nm) (15mm drive, M10x1.5 thread).

Engine — 1999 Chevrolet Blazer

Engine bolt-by-bolt torque for the 1999 Chevrolet Blazer, including the long block, valve covers, and intake. The distributor clamp bolt uses a 13mm drive on a M8x1.25 thread, torqued to 25 ft-lbs (34 Nm). The exhaust manifold bolt torques to 26 ft-lbs (35 Nm) (15mm drive, M10x1.5 thread). plan for a 16mm tool on a M14x1.25 stud; final torque is 15 ft-lbs (20 Nm) (spark plug). Water pump bolt tightens to 18 ft-lbs (24 Nm), takes a 13mm driver, runs on M8x1.25 threads. The engine mount through bolt uses a 18mm drive on a M12x1.75 thread, torqued to 75 ft-lbs (102 Nm). The oil drain plug torques to 20 ft-lbs (27 Nm) (15mm drive, M14x1.5 thread). plan for a 8mm tool on a 3/8"-16 UNC stud; final torque is 89 in-lbs (10 Nm) (valve cover bolt). Timing chain cover bolt tightens to 106 in-lbs (12 Nm), takes a 10mm driver, runs on M8x1.25 threads. The intake manifold bolt (lower) uses a 13mm drive on a 3/8"-16 UNC thread, torqued to 35 ft-lbs (47 Nm). The crankshaft pulley bolt torques to 85 ft-lbs (115 Nm) (1-1/8" drive, 1-1/16" hex thread).

Drivetrain — 1999 Chevrolet Blazer

Drivetrain and driveline fasteners for the 1999 Chevrolet Blazer — axle, transmission, and differential plugs. The transfer case drain plug torques to 32 ft-lbs (43 Nm) (3/8" square drive drive, 3/8" square drive thread). plan for a 13mm tool on a M8x1.25 stud; final torque is 20 ft-lbs (27 Nm) (rear differential cover bolt). Front differential cover bolt tightens to 15 ft-lbs (20 Nm), takes a 13mm driver, runs on M8x1.25 threads.

Suspension — 1999 Chevrolet Blazer

Suspension and chassis fastener torque for the 1999 Chevrolet Blazer — strut, control arm, and sway bar values. plan for a 15mm tool on a M10x1.5 stud; final torque is 24 ft-lbs (32 Nm) (sway bar bracket bolt). Lower ball joint nut tightens to 94 ft-lbs (127 Nm), takes a 1-1/16" driver, runs on M14x1.5 threads. The upper ball joint nut uses a 1-1/16" drive on a 7/16-20 UNF thread, torqued to 37 ft-lbs (50 Nm). The shock upper nut torques to 15 ft-lbs (20 Nm) (15mm drive, M10x1.25 thread). plan for a 15/16" tool on a M12x1.5 stud; final torque is 35 ft-lbs (47 Nm) (tie rod end nut). Rear shock upper bolt tightens to 81 ft-lbs (110 Nm), takes a 15mm driver, runs on M10x1.5 threads. The sway bar link nut uses a 15mm drive on a M10x1.25 thread, torqued to 17 ft-lbs (23 Nm). The wheel bearing hub bolt torques to 180 ft-lbs (244 Nm) (35mm drive, M22x1.5 thread). plan for a 18mm tool on a M12x1.75 stud; final torque is 85 ft-lbs (115 Nm) (rear leaf spring u-bolt nut). Front shock lower bolt tightens to 65 ft-lbs (88 Nm), takes a 18mm driver, runs on M12x1.75 threads. The front shock upper nut uses a 15mm drive on a M10x1.25 thread, torqued to 15 ft-lbs (20 Nm).

Steering — 1999 Chevrolet Blazer

Steering linkage fasteners on the 1999 Chevrolet Blazer. Steering shaft pinch bolt tightens to 35 ft-lbs (47 Nm), takes a 15mm driver, runs on M10x1.5 threads. The pitman arm nut uses a 27mm drive on a M20x1.5 thread, torqued to 185 ft-lbs (251 Nm). The steering box mounting bolt torques to 80 ft-lbs (108 Nm) (21mm drive, M14x1.5 thread). plan for a 18mm tool on a M12x1.75 stud; final torque is 65 ft-lbs (88 Nm) (idler arm bolt).

Body — 1999 Chevrolet Blazer

Body fasteners on the 1999 Chevrolet Blazer. The seat belt anchor bolt uses a 18mm drive on a M12x1.5 thread, torqued to 35 ft-lbs (47 Nm).

Transmission — 1999 Chevrolet Blazer

Transmission fasteners on the 1999 Chevrolet Blazer. The transmission pan bolt torques to 12 ft-lbs (16 Nm) (10mm drive, M8x1.25 thread). plan for a 15mm tool on a M10x1.5 stud; final torque is 35 ft-lbs (47 Nm) (transmission-to-engine bolt).

Wheels & Tires — 1999 Chevrolet Blazer

Wheels & Tires fasteners on the 1999 Chevrolet Blazer. plan for a 21mm tool on a M12x1.5 stud; final torque is 100 ft-lbs (136 Nm) (lug nut).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1999 Chevrolet Blazer numbers above.

Loading the interactive 1999 Chevrolet Blazer fastener lookup with per-bolt filtering, part links, and torque tools…