2008 Chrysler Sebring Lug Nut Torque & Bolt Specs

The 2008 Chrysler Sebring lug nut torque is 110 ft-lbs (150 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 110 ft-lbs (150 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2008 Chrysler Sebring. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 2008 Chrysler Sebring

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2008 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2008 Chrysler Sebring?

The OEM-specified lug-nut torque for the 2008 Chrysler Sebring is 110 ft-lbs (150 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2008 Chrysler Sebring lug nuts?

The 2008 Chrysler Sebring uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2008 Chrysler Sebring fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Chrysler Sebring years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2008 Chrysler Sebring suspension & steering torque specs (control arm, ball joint, tie rod)

All 17 2008 Chrysler Sebring fastener specs

Per-bolt torque, wrench size, and thread spec for the 2008 Chrysler Sebring, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2008 Chrysler Sebring

Wheel and lug nut spec for the 2008 Chrysler Sebring. Lug nut tightens to 110 ft-lbs (150 Nm), takes a 19mm driver, runs on M12x1.5 threads.

Brakes — 2008 Chrysler Sebring

Brake fasteners on the 2008 Chrysler Sebring — caliper bracket, slide pins, and banjo bolt torque follow. The rear brake caliper guide-pin bolt, torqued to 32 ft-lbs (43 Nm). The front brake caliper bracket bolt torques to 80 ft-lbs (108 Nm). plan for the right driver; final torque is 32 ft-lbs (43 Nm) (front brake caliper guide-pin bolt).

Engine — 2008 Chrysler Sebring

Engine bolt-by-bolt torque for the 2008 Chrysler Sebring, including the long block, valve covers, and intake. The spark plug torques to 15 ft-lbs (20 Nm). plan for the right driver; final torque is 25 ft-lbs (34 Nm) (engine oil drain plug).

Drivetrain — 2008 Chrysler Sebring

Drivetrain and driveline fasteners for the 2008 Chrysler Sebring — axle, transmission, and differential plugs. plan for the right driver; final torque is 118 ft-lbs (160 Nm) (front axle/hub nut).

Suspension — 2008 Chrysler Sebring

Suspension and chassis fastener torque for the 2008 Chrysler Sebring — strut, control arm, and sway bar values. Rear wheel hub/bearing bolts tightens to 77 ft-lbs (104 Nm). The lower ball joint pinch bolt, torqued to 70 ft-lbs (95 Nm). The front sway bar end-link nut torques to 35 ft-lbs (47 Nm). plan for the right driver; final torque is 103 ft-lbs (140 Nm) (front strut-to-knuckle bolts). Front lower control arm front pivot bolt tightens to 129 ft-lbs (175 Nm). The front lower control arm rear pivot bolt, torqued to 107 ft-lbs (145 Nm). The rear shock lower bolt torques to 73 ft-lbs (99 Nm). plan for the right driver; final torque is 40 ft-lbs (54 Nm) (front strut upper mount nuts). Front wheel hub-to-knuckle bolts tightens to 35 ft-lbs (47 Nm).

Steering — 2008 Chrysler Sebring

Steering linkage fasteners on the 2008 Chrysler Sebring. The outer tie rod end nut, torqued to 40 ft-lbs (54 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2008 Chrysler Sebring numbers above.

Loading the interactive 2008 Chrysler Sebring fastener lookup with per-bolt filtering, part links, and torque tools…