2019–2020 Kia K900 Lug Nut Torque & Bolt Specs

The 2020 Kia K900 lug nut torque is 87 ft-lbs, tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 87 ft-lbs · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2020 Kia K900. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

These specifications also apply to the 2019 model years — identical specs on file for each year.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2020 Kia K900

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2020 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2020 Kia K900?

The OEM-specified lug-nut torque for the 2020 Kia K900 is 87 ft-lbs, using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2020 Kia K900 lug nuts?

The 2020 Kia K900 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2020 Kia K900 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia K900 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2020 Kia K900 oil drain plug torque & size

→ 2020 Kia K900 suspension & steering torque specs (control arm, ball joint, tie rod)

All 16 2020 Kia K900 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2020 Kia K900, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2020 Kia K900

Wheel and lug nut spec for the 2020 Kia K900. For the all four wheels, plan for a 21mm tool on a M12x1.5 stud; final torque is 80 ft-lbs (108 Nm) (lug nut). Wheel lug nut tightens to 87 ft-lbs, takes a 21mm driver, runs on M12x1.5 threads, located at the wheel hub.

Brakes — 2020 Kia K900

Brake fasteners on the 2020 Kia K900 — caliper bracket, slide pins, and banjo bolt torque follow. Rear brake caliper bracket bolt tightens to 65 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the caliper bracket. The front brake caliper slide pin bolt uses a 14mm drive on a M10x1.25 thread, torqued to 26 ft-lbs at the caliper slide. At the caliper bracket, the front brake caliper bracket bolt torques to 87 ft-lbs (19mm drive, M14x1.5 thread). For the caliper slide, plan for a 14mm tool on a M10x1.25 stud; final torque is 22 ft-lbs (rear brake caliper slide pin bolt).

Engine — 2020 Kia K900

Engine bolt-by-bolt torque for the 2020 Kia K900, including the long block, valve covers, and intake. The intake manifold bolt uses a 12mm drive on a M8x1.25 thread, torqued to 18 ft-lbs at the intake manifold. At the valve cover, the valve cover bolt torques to 9 ft-lbs (10mm drive, M6x1.0 thread). For the exhaust manifold, plan for a 14mm tool on a M10x1.25 stud; final torque is 33 ft-lbs (exhaust manifold bolt). Oil pan drain plug tightens to 29 ft-lbs, takes a 17mm driver, runs on M14x1.5 threads, located at the oil pan.

Suspension — 2020 Kia K900

Suspension and chassis fastener torque for the 2020 Kia K900 — strut, control arm, and sway bar values. At the control arm, the rear lower control arm bolt torques to 65 ft-lbs (19mm drive, M14x1.5 thread). For the strut top mount, plan for a 17mm tool on a M12x1.25 stud; final torque is 43 ft-lbs (front strut top mount nut). Front ball joint nut tightens to 65 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the ball joint. The front lower control arm bolt uses a 19mm drive on a M14x1.5 thread, torqued to 65 ft-lbs at the control arm. At the sway bar link, the sway bar link nut torques to 37 ft-lbs (14mm drive, M10x1.25 thread).

Transmission — 2020 Kia K900

Transmission fasteners on the 2020 Kia K900. For the transmission mount, plan for a 17mm tool on a M12x1.5 stud; final torque is 58 ft-lbs (transmission mount bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2020 Kia K900 numbers above.

Loading the interactive 2020 Kia K900 fastener lookup with per-bolt filtering, part links, and torque tools…