2024 Kia Sorento Lug Nut Torque & Bolt Specs

The 2024 Kia Sorento lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm hex socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm hex · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2024 Kia Sorento. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2024 Kia Sorento

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Kia Sorento?

The OEM-specified lug-nut torque for the 2024 Kia Sorento is 80 ft-lbs (108 Nm), using a 21mm hex socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Kia Sorento lug nuts?

The 2024 Kia Sorento uses a 21mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Kia Sorento fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia Sorento years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Kia Sorento oil drain plug torque & size

→ 2024 Kia Sorento suspension & steering torque specs (control arm, ball joint, tie rod)

→ 2024 Kia Sorento axle nut torque spec (CV axle & hub nut)

→ 2024 Kia Sorento brake job torque specs (caliper, bracket & slide pins)

All 21 2024 Kia Sorento fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Kia Sorento, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 21 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Brakes — 2024 Kia Sorento

Brake fasteners on the 2024 Kia Sorento — caliper bracket, slide pins, and banjo bolt torque follow. For the caliper slide, plan for a 12mm tool on a M8x1.25 stud; final torque is 16 ft-lbs (rear slide). Front slide tightens to 26 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the caliper slide. The front bracket uses a 17mm drive on a M12x1.5 thread, torqued to 85 ft-lbs at the caliper bracket. At the front knuckle, the front brake caliper bracket bolt torques to 65 ft-lb (14mm hex drive, M12 thread). For the caliper bracket, plan for a 14mm tool on a M10x1.25 stud; final torque is 41 ft-lbs (rear bracket). Front brake caliper slide pin tightens to 22 ft-lb, takes a 12mm hex driver, runs on M10 threads, located at the front caliper. OEM-verified spec.

Engine — 2024 Kia Sorento

Engine bolt-by-bolt torque for the 2024 Kia Sorento, including the long block, valve covers, and intake. Oil drain plug tightens to 25 ft-lbs (34 Nm), takes a 17mm driver, runs on M14x1.5 threads, located at the oil pan. The valve cover uses a 10mm drive on a M6x1.0 thread, torqued to 7 ft-lbs at the valve cover. At the oil pan, the oil pan torques to 29 ft-lbs (17mm drive, M14x1.5 thread). For the exhaust manifold, plan for a 14mm tool on a M10x1.25 stud; final torque is 25 ft-lbs (exhaust). Spark plug tightens to 18 ft-lbs (24 Nm), takes a 5/8" (16mm) driver, runs on M14x1.25 threads, located at the cylinder head. The intake uses a 12mm drive on a M8x1.25 thread, torqued to 19 ft-lbs at the intake manifold.

Drivetrain — 2024 Kia Sorento

Drivetrain and driveline fasteners for the 2024 Kia Sorento — axle, transmission, and differential plugs. The front axle hub nut uses a 32mm hex drive on a M24 thread, torqued to 214 ft-lb at the front hub.

Suspension — 2024 Kia Sorento

Suspension and chassis fastener torque for the 2024 Kia Sorento — strut, control arm, and sway bar values. At the control arm, the control arm torques to 65 ft-lbs (19mm drive, M14x1.5 thread). For the ball joint, plan for a 19mm tool on a M14x1.5 stud; final torque is 49 ft-lbs (ball joint). Sway bar tightens to 23 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the sway bar link. The strut uses a 17mm drive on a M12x1.5 thread, torqued to 40 ft-lbs at the strut top mount.

Wheel Hardware — 2024 Kia Sorento

Wheel Hardware fasteners on the 2024 Kia Sorento. For the all wheels, plan for a 21mm hex tool on a M12x1.5 stud; final torque is 80 ft-lbs (108 Nm) (lug nut).

Transmission — 2024 Kia Sorento

Transmission fasteners on the 2024 Kia Sorento. Cv axle nut tightens to 160 ft-lbs, takes a 24mm driver, runs on M18x1.5 threads, located at the rear axle. The flywheel uses a 19mm drive on a M14x1.5 thread, torqued to 65 ft-lbs at the engine block. At the transmission mount, the trans mount torques to 44 ft-lbs (14mm drive, M10x1.25 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Kia Sorento numbers above.

Loading the interactive 2024 Kia Sorento fastener lookup with per-bolt filtering, part links, and torque tools…