2008 Nissan Pathfinder Lug Nut Torque & Bolt Specs

The 2008 Nissan Pathfinder lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2008 Nissan Pathfinder. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2008 Nissan Pathfinder

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2008 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2008 Nissan Pathfinder?

The OEM-specified lug-nut torque for the 2008 Nissan Pathfinder is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2008 Nissan Pathfinder lug nuts?

The 2008 Nissan Pathfinder uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2008 Nissan Pathfinder fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Pathfinder years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 13 2008 Nissan Pathfinder fastener specs

Per-bolt torque, wrench size, and thread spec for the 2008 Nissan Pathfinder, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 6 of the 13 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Engine — 2008 Nissan Pathfinder

Engine bolt-by-bolt torque for the 2008 Nissan Pathfinder, including the long block, valve covers, and intake. The exhaust manifold nut uses a 14mm drive on a M8x1.25 thread, torqued to 21 ft-lb (28 Nm) at the vq40de exhaust manifold. At the cylinder head — vq40de, the spark plug torques to 18 ft-lbs (24 Nm) (9/16" (14mm) drive, M14x1.25 thread). For the oil pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Intake manifold bolt tightens to 8 ft-lb (11 Nm), takes a 10mm driver, runs on M8x1.25 threads, located at the vq40de intake manifold. The oil filter uses a 65mm cap wrench drive, torqued to Hand tight + 3/4 turn at the engine oil filter housing. OEM-verified spec.

Drivetrain — 2008 Nissan Pathfinder

Drivetrain and driveline fasteners for the 2008 Nissan Pathfinder — axle, transmission, and differential plugs. At the transfer case (4wd), the transfer case drain plug torques to 25 ft-lb (34 Nm) (24mm drive). For the front wheel hub / cv axle, plan for a 36mm tool on a M24x1.5 stud; final torque is 101 ft-lb (137 Nm) (front axle hub nut). Confirmed against manufacturer service literature.

Suspension — 2008 Nissan Pathfinder

Suspension and chassis fastener torque for the 2008 Nissan Pathfinder — strut, control arm, and sway bar values. For the front strut lower pinch, plan for a 19mm tool on a M12x1.25 stud; final torque is 86 ft-lb (117 Nm) (front strut-to-knuckle bolt).

Brake — 2008 Nissan Pathfinder

Brake fasteners on the 2008 Nissan Pathfinder. Front caliper bracket bolt tightens to 136 ft-lb (184 Nm), takes a 19mm driver, runs on M14x1.5 threads, located at the caliper bracket to knuckle. This figure is independently verified against OEM service data. The rear caliper bracket bolt uses a 17mm drive on a M12x1.25 thread, torqued to 76 ft-lb (103 Nm) at the rear caliper bracket to knuckle. OEM-verified spec. At the rear caliper to bracket, the rear brake caliper bolt torques to 20 ft-lb (27 Nm) (14mm drive, M10x1.25 thread). Confirmed against manufacturer service literature. For the front caliper to bracket, plan for a 14mm tool on a M10x1.25 stud; final torque is 20 ft-lb (27 Nm) (front brake caliper bolt). This figure is independently verified against OEM service data.

Wheels & Tires — 2008 Nissan Pathfinder

Wheels & Tires fasteners on the 2008 Nissan Pathfinder. The lug nut uses a 21mm drive on a M12x1.25 thread, torqued to 80 ft-lbs (108 Nm) at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2008 Nissan Pathfinder numbers above.

Loading the interactive 2008 Nissan Pathfinder fastener lookup with per-bolt filtering, part links, and torque tools…