2016 Nissan Pathfinder Lug Nut Torque & Bolt Specs

The 2016 Nissan Pathfinder lug nut torque is 83 ft-lb (113 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 5x114.3.

Lug nut torque: 83 ft-lb (113 Nm) · Socket size: 21mm · Thread: M12x1.25 · Bolt pattern: 5x114.3.

This page is the OEM-referenced fastener summary for the 2016 Nissan Pathfinder. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2016 Nissan Pathfinder

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2016 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2016 Nissan Pathfinder?

The OEM-specified lug-nut torque for the 2016 Nissan Pathfinder is 83 ft-lb (113 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2016 Nissan Pathfinder lug nuts?

The 2016 Nissan Pathfinder uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2016 Nissan Pathfinder fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Pathfinder years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2016 Nissan Pathfinder oil drain plug torque & size

All 14 2016 Nissan Pathfinder fastener specs

Per-bolt torque, wrench size, and thread spec for the 2016 Nissan Pathfinder, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 10 of the 14 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Engine — 2016 Nissan Pathfinder

Engine bolt-by-bolt torque for the 2016 Nissan Pathfinder, including the long block, valve covers, and intake. Oil drain plug tightens to 25 ft-lb (34 Nm), takes a 14mm driver, runs on M14x1.5 threads, located at the oil pan. The valve cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 7 ft-lb (9 Nm) at the vq35de valve cover. At the engine oil filter housing, the oil filter torques to Hand tight + 3/4 turn (65mm cap wrench drive). Confirmed against manufacturer service literature. For the cylinder head — vq35de, plan for a 10mm 12-pt tool on a M11x1.25 stud; final torque is 72 ft-lb → loosen → 26–32 ft-lb → +90° → +90° (see notes) (cylinder head bolt). This figure is independently verified against OEM service data. Spark plug tightens to 15–21 ft-lb (20–28 Nm), takes a 5/8" (16mm) driver, runs on M14x1.25 threads, located at the cylinder head — vq35de. OEM-verified spec.

Drivetrain — 2016 Nissan Pathfinder

Drivetrain and driveline fasteners for the 2016 Nissan Pathfinder — axle, transmission, and differential plugs. The cvt drain plug uses a 10mm Allen drive, torqued to 25 ft-lb (34 Nm) at the cvt transmission pan. OEM-verified spec. At the front wheel hub / cv axle, the front axle hub nut torques to 101 ft-lb (137 Nm) (36mm drive, M24x1.5 thread). Confirmed against manufacturer service literature.

Suspension — 2016 Nissan Pathfinder

Suspension and chassis fastener torque for the 2016 Nissan Pathfinder — strut, control arm, and sway bar values. At the front strut lower pinch, the front strut-to-knuckle bolt torques to 86 ft-lb (117 Nm) (19mm drive, M12x1.25 thread).

Brake — 2016 Nissan Pathfinder

Brake fasteners on the 2016 Nissan Pathfinder. For the rear caliper to bracket, plan for a 14mm tool on a M10x1.25 stud; final torque is 20 ft-lb (27 Nm) (rear brake caliper bolt). This figure is independently verified against OEM service data. Front caliper bracket bolt (front) tightens to 91 ft-lb (123 Nm), takes a 19mm driver, runs on M14x1.5 threads, located at the front torque member to knuckle. OEM-verified spec. The front brake caliper bolt uses a 17mm drive on a M12x1.25 thread, torqued to 34 ft-lb (46 Nm) at the front caliper to bracket. Confirmed against manufacturer service literature. At the rear caliper bracket to knuckle, the rear caliper bracket bolt torques to 76 ft-lb (103 Nm) (17mm drive, M12x1.25 thread). This figure is independently verified against OEM service data. For the caliper bracket to knuckle, plan for a 22mm tool on a M14x1.5 stud; final torque is 107 ft-lb (145 Nm) (front caliper bracket bolt). OEM-verified spec.

Wheels & Tires — 2016 Nissan Pathfinder

Wheels & Tires fasteners on the 2016 Nissan Pathfinder. Lug nut tightens to 83 ft-lb (113 Nm), takes a 21mm driver, runs on M12x1.25 threads, located at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2016 Nissan Pathfinder numbers above.

Loading the interactive 2016 Nissan Pathfinder fastener lookup with per-bolt filtering, part links, and torque tools…