2022 Nissan Pathfinder Lug Nut Torque & Bolt Specs

The 2022 Nissan Pathfinder lug nut torque is 83 ft-lb (113 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 5x114.3.

Lug nut torque: 83 ft-lb (113 Nm) · Socket size: 21mm · Thread: M12x1.25 · Bolt pattern: 5x114.3.

This page is the OEM-referenced fastener summary for the 2022 Nissan Pathfinder. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2022 Nissan Pathfinder

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Nissan Pathfinder?

The OEM-specified lug-nut torque for the 2022 Nissan Pathfinder is 83 ft-lb (113 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Nissan Pathfinder lug nuts?

The 2022 Nissan Pathfinder uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Nissan Pathfinder fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Pathfinder years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Nissan Pathfinder suspension & steering torque specs (control arm, ball joint, tie rod)

All 18 2022 Nissan Pathfinder fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Nissan Pathfinder, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 9 of the 18 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Brakes — 2022 Nissan Pathfinder

Brake fasteners on the 2022 Nissan Pathfinder — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper bracket bolt, torqued to 133 ft-lbs (180 Nm) at the front caliper. This figure is independently verified against OEM service data. At the front caliper, the front brake caliper guide pin bolt torques to 34 ft-lbs (46 Nm). OEM-verified spec.

Engine — 2022 Nissan Pathfinder

Engine bolt-by-bolt torque for the 2022 Nissan Pathfinder, including the long block, valve covers, and intake. At the cylinder head — vq35dd, the spark plug torques to 18 ft-lb (25 Nm) (5/8" (16mm) drive, M14x1.25 thread). For the oil pan, plan for a 14mm tool on a M14x1.5 stud; final torque is 25 ft-lb (34 Nm) (oil drain plug). Valve cover bolt tightens to 7 ft-lb (9 Nm), takes a 10mm driver, runs on M6x1.0 threads, located at the vq35dd valve cover. The oil filter uses a 65mm cap wrench drive, torqued to Hand tight + 3/4 turn at the engine oil filter housing. OEM-verified spec.

Drivetrain — 2022 Nissan Pathfinder

Drivetrain and driveline fasteners for the 2022 Nissan Pathfinder — axle, transmission, and differential plugs. For the front wheel hub / cv axle, plan for a 36mm tool on a M24x1.5 stud; final torque is 101 ft-lb (137 Nm) (front axle hub nut). Confirmed against manufacturer service literature. Rear differential drain plug tightens to 47 ft-lb (64 Nm), takes a 24mm driver, located at the rear differential housing (awd). The transmission drain plug uses a 10mm Allen drive, torqued to 29 ft-lb (39 Nm) at the zf 9-speed transmission pan.

Suspension — 2022 Nissan Pathfinder

Suspension and chassis fastener torque for the 2022 Nissan Pathfinder — strut, control arm, and sway bar values. Front lower control arm bolt tightens to 76 ft-lb (103 Nm), takes a 19mm driver, runs on M14x2.0 threads, located at the front lower control arm to subframe. The front strut-to-knuckle bolt uses a 19mm drive on a M12x1.25 thread, torqued to 86 ft-lb (117 Nm) at the front strut lower pinch. At the front stabilizer bar end link, the front sway bar link nut torques to 33 ft-lb (45 Nm) (17mm drive, M12x1.25 thread).

Wheels & Tires — 2022 Nissan Pathfinder

Wheels & Tires fasteners on the 2022 Nissan Pathfinder. The lug nut uses a 21mm drive on a M12x1.25 thread, torqued to 83 ft-lb (113 Nm) at the wheel hub.

Brake — 2022 Nissan Pathfinder

Brake fasteners on the 2022 Nissan Pathfinder. At the rear caliper to bracket, the rear brake caliper bolt torques to 34 ft-lb (46 Nm) (14mm drive, M10x1.25 thread). Confirmed against manufacturer service literature. For the caliper bleeder, plan for a 8mm tool; final torque is 11 ft-lb (15 Nm) (brake bleeder screw). This figure is independently verified against OEM service data. Front brake caliper bolt tightens to 34 ft-lb (46 Nm), takes a 17mm driver, runs on M12x1.25 threads, located at the front caliper to bracket. OEM-verified spec. The rear caliper bracket bolt uses a 21mm drive on a M14x1.5 thread, torqued to 65 ft-lb (88 Nm) at the rear caliper bracket to knuckle. Confirmed against manufacturer service literature. At the caliper bracket to knuckle, the front caliper bracket bolt torques to 107 ft-lb (145 Nm) (22mm drive, M14x1.5 thread). This figure is independently verified against OEM service data.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Nissan Pathfinder numbers above.

Loading the interactive 2022 Nissan Pathfinder fastener lookup with per-bolt filtering, part links, and torque tools…