2019 Nissan Pathfinder Lug Nut Torque & Bolt Specs

The 2019 Nissan Pathfinder lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2019 Nissan Pathfinder. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2019 Nissan Pathfinder

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2019 Nissan Pathfinder?

The OEM-specified lug-nut torque for the 2019 Nissan Pathfinder is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2019 Nissan Pathfinder lug nuts?

The 2019 Nissan Pathfinder uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2019 Nissan Pathfinder fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Pathfinder years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2019 Nissan Pathfinder oil drain plug torque & size

All 14 2019 Nissan Pathfinder fastener specs

Per-bolt torque, wrench size, and thread spec for the 2019 Nissan Pathfinder, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 10 of the 14 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Engine — 2019 Nissan Pathfinder

Engine bolt-by-bolt torque for the 2019 Nissan Pathfinder, including the long block, valve covers, and intake. For the oil pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Confirmed against manufacturer service literature. Spark plug tightens to 18 ft-lbs (24 Nm), takes a 5/8" (16mm) driver, runs on M14x1.25 threads, located at the cylinder head — vq35de. The oil filter uses a 65mm cap wrench drive, torqued to Hand tight + 3/4 turn at the engine oil filter housing. OEM-verified spec. At the cylinder head — vq35de, the cylinder head bolt torques to 72 ft-lb → loosen → 26–32 ft-lb → +90° → +90° (see notes) (10mm 12-pt drive, M11x1.25 thread). Confirmed against manufacturer service literature. For the vq35de valve cover, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lb (9 Nm) (valve cover bolt).

Drivetrain — 2019 Nissan Pathfinder

Drivetrain and driveline fasteners for the 2019 Nissan Pathfinder — axle, transmission, and differential plugs. Front axle hub nut tightens to 101 ft-lb (137 Nm), takes a 36mm driver, runs on M24x1.5 threads, located at the front wheel hub / cv axle. This figure is independently verified against OEM service data. The cvt drain plug uses a 10mm Allen drive, torqued to 25 ft-lb (34 Nm) at the cvt transmission pan. OEM-verified spec.

Suspension — 2019 Nissan Pathfinder

Suspension and chassis fastener torque for the 2019 Nissan Pathfinder — strut, control arm, and sway bar values. The front strut-to-knuckle bolt uses a 19mm drive on a M12x1.25 thread, torqued to 86 ft-lb (117 Nm) at the front strut lower pinch.

Wheels & Tires — 2019 Nissan Pathfinder

Wheels & Tires fasteners on the 2019 Nissan Pathfinder. At the wheel hub, the lug nut torques to 80 ft-lbs (108 Nm) (21mm drive, M12x1.25 thread).

Brake — 2019 Nissan Pathfinder

Brake fasteners on the 2019 Nissan Pathfinder. For the rear caliper bracket to knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 76 ft-lb (103 Nm) (rear caliper bracket bolt). This figure is independently verified against OEM service data. Front brake caliper bolt tightens to 34 ft-lb (46 Nm), takes a 17mm driver, runs on M12x1.25 threads, located at the front caliper to bracket. OEM-verified spec. The rear brake caliper bolt uses a 14mm drive on a M10x1.25 thread, torqued to 20 ft-lb (27 Nm) at the rear caliper to bracket. Confirmed against manufacturer service literature. At the caliper bracket to knuckle, the front caliper bracket bolt torques to 107 ft-lb (145 Nm) (22mm drive, M14x1.5 thread). This figure is independently verified against OEM service data. For the front torque member to knuckle, plan for a 19mm tool on a M14x1.5 stud; final torque is 91 ft-lb (123 Nm) (front caliper bracket bolt (front)). OEM-verified spec.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 Nissan Pathfinder numbers above.

Loading the interactive 2019 Nissan Pathfinder fastener lookup with per-bolt filtering, part links, and torque tools…