2011 Toyota Tacoma Lug Nut Torque & Bolt Specs

The 2011 Toyota Tacoma lug nut torque is 83 ft-lbs (113 Nm), tightened with a 21mm (13/16") socket on M12 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 6x139.7.

Lug nut torque: 83 ft-lbs (113 Nm) · Socket size: 21mm (13/16") · Thread: M12 x 1.5 · Bolt pattern: 6x139.7.

This page is the OEM-referenced fastener summary for the 2011 Toyota Tacoma. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2011 Toyota Tacoma

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2011 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2011 Toyota Tacoma?

The OEM-specified lug-nut torque for the 2011 Toyota Tacoma is 83 ft-lbs (113 Nm), using a 21mm (13/16") socket on M12 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2011 Toyota Tacoma lug nuts?

The 2011 Toyota Tacoma uses a 21mm (13/16") socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2011 Toyota Tacoma fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Tacoma years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2011 Toyota Tacoma oil drain plug torque & size

→ 2011 Toyota Tacoma suspension & steering torque specs (control arm, ball joint, tie rod)

All 44 2011 Toyota Tacoma fastener specs

Per-bolt torque, wrench size, and thread spec for the 2011 Toyota Tacoma, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2011 Toyota Tacoma

Wheel and lug nut spec for the 2011 Toyota Tacoma. The lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 83 ft-lbs (113 Nm) at the all four wheels.

Brakes — 2011 Toyota Tacoma

Brake fasteners on the 2011 Toyota Tacoma — caliper bracket, slide pins, and banjo bolt torque follow. At the all brake line fittings (flare nut). use flare wrench to prevent rounding. do not use open-end wrench., the brake line union nut torques to 11 ft-lbs (15 Nm) (10mm flare wrench drive, 3/8" flare nut thread). For the front caliper mounting/bracket bolts for gen2 (2005-2015) and gen3 (2016-2023). two bolts per side. confirmed for 4wd and 2wd., plan for a 19mm tool on a M14 stud; final torque is 91 ft-lbs (123 Nm) (front brake caliper bracket bolts — gen2/gen3). Abs wheel speed sensor bolt (brake system) tightens to 71 in-lbs (5.9 ft-lbs) ft-lbs (8 Nm), takes a 10mm driver, runs on M6 threads, located at the see also suspension section. both front and rear abs sensors = 71 in-lbs.. The rear drum brake backing plate x axle housing uses a 14mm drive on a M12 thread, torqued to 48 ft-lbs (68 Nm) at the backing plate (dust shield) bolt torque for drum brake rear axles. gen1 fsm: 50 ft-lbs (68 nm).. At the sliding guide pin bolts (the smaller bolts, not the bracket bolts). apply caliper grease/silicone lube to guide pins before installation., the front caliper slide pin bolts torques to 25 ft-lbs (34 Nm) (12mm or 14mm depending on year drive, M10 thread).

Engine — 2011 Toyota Tacoma

Engine bolt-by-bolt torque for the 2011 Toyota Tacoma, including the long block, valve covers, and intake. For the thermostat housing bolts. use new o-ring., plan for a 12mm tool on a M8 stud; final torque is 13 ft-lbs (18 Nm) (thermostat / water inlet housing). Camshaft timing gear x camshaft (cam sprocket bolt) tightens to 58 ft-lbs (78 Nm), takes a 17mm or cam holding tool driver, runs on M14 threads, located at the vvt-i cam gear. apply engine oil. hold cam with wrench or sst.. The cylinder head bolts (main bolts) uses a 12mm 12-point socket drive on a M11 (12-point) thread, torqued to Step 1: 29 ft-lbs | Step 2: +90° | Step 3: +90° ft-lbs (Step 1: 39 Nm Nm) at the tty 3-pass method. same angle sequence as 5vz-fe. 10 main bolts in this engine. tighten in specified sequence (start from center, work outward).. At the tighten in sequence. 5 bearing caps. sohc engine — single camshaft., the camshaft bearing cap x cylinder head torques to Bolt A: 9 ft-lbs | Others: 11 ft-lbs ft-lbs (Bolt A: 12 Nm | Others: 15.5 Nm Nm) (12mm drive, M8 thread). For the front mount-to-frame., plan for a 14mm tool on a M12 stud; final torque is 28 ft-lbs (38 Nm) (engine mounting insulator front x body (frame)). Connecting rod bolts tightens to Step 1: 18 ft-lbs | Step 2: +90° ft-lbs (Step 1: 25 Nm Nm), takes a 12mm driver, runs on M9 threads, located at the tty. replace after removal.. The main bearing cap x cylinder block (crankshaft bearing caps) uses a 14mm drive on a M11 thread, torqued to Step 1: 29 ft-lbs | Step 2: +90° ft-lbs (Step 1: 39 Nm Nm) at the 5 main bearing caps. after tightening, verify crankshaft rotates smoothly.. At the chain-driven water pump. new o-ring required., the water pump x timing chain cover torques to 75 in-lbs (6.3 ft-lbs) ft-lbs (8.5 Nm) (10mm drive, M6 thread). For the use new crush washer. slightly different from v6 models (v6 = 30 ft-lbs)., plan for a 14mm tool on a M14 x 1.5 stud; final torque is 28 ft-lbs (38 Nm) (oil drain plug). Crankshaft pulley x crankshaft tightens to 192 ft-lbs (260 Nm), takes a 22mm hex (use crankshaft holding SST) driver, runs on M22 x 1.5 threads, located at the slightly higher than v6 spec (192 vs 184 ft-lbs). uses timing chain, not belt. clean threads, apply engine oil.. The spark plug uses a 5/8" spark plug socket drive on a 14mm x 1.25 thread, torqued to 13 ft-lbs (18 Nm) at the 5 plugs total (i4 engine). access from top after removing single valve cover.. At the engine, the cylinder head bolt torques to Stage 1: 40 ft-lbs, Stage 2: +90° (14mm drive, M10x1.5 thread). For the 19 bolts and 2 nuts. tighten uniformly in multiple passes., plan for a 10mm tool on a 6mm stud; final torque is 80 in-lbs (6.7 ft-lbs) ft-lbs (9 Nm) (valve cover (cylinder head cover x cylinder head)). Engine mounting bracket front x cylinder block (rh and lh) tightens to 38 ft-lbs (51 Nm), takes a 14mm driver, runs on M12 threads, located at the front engine mount brackets to block.. The oil pan bolts (oil pan x cylinder block) uses a 12mm drive on a M8 thread, torqued to 19 ft-lbs (26 Nm) at the lower oil pan (no. 2): 80 in-lbs. oil drain plug: 28 ft-lbs (38 nm).. At the engine, the connecting rod bolt torques to Stage 1: 18 ft-lbs, Stage 2: +45° (13mm drive, M9x1.0 thread). For the plastic intake manifold. tighten in criss-cross pattern. do not overtighten., plan for a 12mm tool on a M8 stud; final torque is 15 ft-lbs (20 Nm) (intake manifold x cylinder head). Exhaust manifold x cylinder head tightens to 27 ft-lbs (36 Nm), takes a 14mm driver, runs on M10 threads, located at the 6 nuts. use anti-seize on studs. tighten from center outward..

Drivetrain — 2011 Toyota Tacoma

Drivetrain and driveline fasteners for the 2011 Toyota Tacoma — axle, transmission, and differential plugs. Front axle hub nut (4wd) — gen2 2005-2015 tightens to 203 ft-lbs (275 Nm), takes a 35mm socket driver, runs on M22 x 1.5 threads, located at the updated spec for gen2 — higher than gen1. use new cotter pin and adjust lock cap. install cotter pin without reducing torque.. The front cv / birfield joint hub bolts (hub x steering knuckle) — gen2 uses a 17mm drive on a M12 thread, torqued to 60 ft-lbs (81 Nm) at the four hub-to-knuckle bolts. tighten in cross pattern. note: gen3 hub bolts = 91 ft-lbs per service data..

Suspension — 2011 Toyota Tacoma

Suspension and chassis fastener torque for the 2011 Toyota Tacoma — strut, control arm, and sway bar values. The abs wheel speed sensor bolt uses a 10mm drive on a M6 thread, torqued to 71 in-lbs (5.9 ft-lbs) ft-lbs (8 Nm) at the front and rear abs speed sensor bolts to steering knuckle/axle housing. also sensor wire harness clamp bolts = same spec.. At the lower ball joint mount bolts (2 bolts attaching lower bj to knuckle) = 118 ft-lbs. confirmed for 2005-2015 4wd., the lower ball joint — gen2 2005-2015 torques to 118 ft-lbs (160 Nm) (19mm drive, M14 (knuckle bolts) thread). For the 83 ft-lbs for all gen1/2/3 tacomas (1995–2023). thread size: m12 x 1.5 for all years. flat-seat washer-type lug nuts. 6-lug pattern on 4wd, 5-lug on some 2wd models. tighten in star pattern. note: gen4 (2024+) changed to m14 x 1.5 at 103.5 ft-lbs., plan for a 21mm (13/16") tool on a M12 x 1.5 stud; final torque is 83 ft-lbs (113 Nm) (lug nuts — all generations gen1/gen2/gen3). Strut mount nut tightens to 47 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the strut tower. The tie rod end to knuckle nut — gen1 4wd, gen2, gen3 uses a 22mm drive on a M14 thread, torqued to 67 ft-lbs (90 Nm) at the outer tie rod nut = 67 ft-lbs. can advance up to additional 60° to align cotter pin. applies gen1 4wd (90 nm = 67 ft-lbs), gen2, and gen3.. At the front leaf spring eye bolt to hanger bracket. with suspension loaded at ride height., the rear leaf spring front hanger bolt x frame torques to 116 ft-lbs (157 Nm) (24mm drive, M16 thread). For the gen1 and gen2. upper mount (shock to suspension support): 22 ft-lbs (gen1 4wd). gen3 lower shock = 61 ft-lbs; upper = 14 ft-lbs (strut top nut)., plan for a 21mm tool on a M14 stud; final torque is 101 ft-lbs (135 Nm) (front shock absorber lower mount x lower control arm). Lower control arm x frame — gen2 2005-2015 tightens to 96 ft-lbs (130 Nm), takes a 24mm driver, runs on M16 threads, located at the gen2 lower control arm pivot bolts. lower shock bolt: 101 ft-lbs.. The upper control arm x frame — gen2 2005-2015 uses a 21mm drive on a M14 thread, torqued to 87 ft-lbs (115 Nm) at the upper suspension arm to frame bolts.. At the oem u-bolt torque: 90 ft-lbs per adventuretaco.com oem data. some fsm versions cite 37 ft-lbs — that appears to be an early/outdated value. use 90 ft-lbs with oem u-bolts at ride height. re-torque after 100 miles., the rear leaf spring u-bolt nuts — gen2/gen3 oem torques to 90 ft-lbs (123 Nm) (19mm deep drive, 9/16" (OEM U-bolt size) thread). For the wheel hub, plan for a 21mm tool on a M12x1.5 stud; final torque is 76 ft-lbs (wheel lug nut). Rear leaf spring shackle — gen2/gen3 tightens to 89 ft-lbs (121 Nm), takes a 24mm driver, runs on M16 threads, located at the rear shackle pin nuts = 89 ft-lbs. front hanger = 89 ft-lbs. tighten at ride height.. The sway bar link nut uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the sway bar. At the tighten to 81 ft-lbs then advance up to additional 60° to align cotter pin slot — do not back off. use new cotter pin., the upper ball joint nut — gen2 2005-2015 torques to 81 ft-lbs (110 Nm) (22mm drive, M14 thread).

Body — 2011 Toyota Tacoma

Body fasteners on the 2011 Toyota Tacoma. At the no explicit torque value found in gen1/gen2/gen3 toyota fsm. community consensus and toyota technician guidance: 50–60 ft-lbs with blue loctite. use anti-seize on threads to prevent corrosion bonding (especially gen1 older trucks). apply in a cross-pattern from center outward., the cab mount bolts (body-to-frame) torques to 50–60 ft-lbs (OEM spec not formally published in FSM) ft-lbs (68–81 Nm Nm) (22mm drive, M14 x 2.0 thread). For the no specific fsm torque value. per toyota technician and forum data: 50–60 ft-lbs with anti-seize or blue loctite. gen2 and gen3 share same bed mount design. 4 to 6 bed bolts per side. check for corrosion on older trucks before removal., plan for a 19mm or 22mm (varies by year) tool on a M14 x 2.0 stud; final torque is 50–60 ft-lbs (OEM spec not formally published) ft-lbs (68–81 Nm Nm) (bed mount bolts (cargo bed x frame)).

Interior — 2011 Toyota Tacoma

Interior fasteners on the 2011 Toyota Tacoma. For the floor pan, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (center console bolt). Seat belt anchor bolt tightens to 43 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the b-pillar.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2011 Toyota Tacoma numbers above.

Loading the interactive 2011 Toyota Tacoma fastener lookup with per-bolt filtering, part links, and torque tools…