2020 Toyota Tundra Lug Nut Torque & Bolt Specs

The 2020 Toyota Tundra lug nut torque is 97 ft-lbs (131 Nm), tightened with a 21mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 97 ft-lbs (131 Nm) · Socket size: 21mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2020 Toyota Tundra. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2020 Toyota Tundra

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2020 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2020 Toyota Tundra?

The OEM-specified lug-nut torque for the 2020 Toyota Tundra is 97 ft-lbs (131 Nm), using a 21mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2020 Toyota Tundra lug nuts?

The 2020 Toyota Tundra uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2020 Toyota Tundra fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Tundra years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2020 Toyota Tundra oil drain plug torque & size

→ 2020 Toyota Tundra suspension & steering torque specs (control arm, ball joint, tie rod)

All 23 2020 Toyota Tundra fastener specs

Per-bolt torque, wrench size, and thread spec for the 2020 Toyota Tundra, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2020 Toyota Tundra

Brake fasteners on the 2020 Toyota Tundra — caliper bracket, slide pins, and banjo bolt torque follow. At the rotor face, the brake rotor set screw torques to 4 ft-lbs (5mm drive, M5x0.8 thread). For the caliper, plan for a 10mm tool on a M10x1.0 stud; final torque is 25 ft-lbs (brake line banjo bolt). Brake caliper pin tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the caliper bracket. The caliper bracket bolt uses a 17mm drive on a M12x1.25 thread, torqued to 85 ft-lbs at the steering knuckle.

Engine — 2020 Toyota Tundra

Engine bolt-by-bolt torque for the 2020 Toyota Tundra, including the long block, valve covers, and intake. For the front of engine, plan for a 14mm tool on a M10x1.25 stud; final torque is 33 ft-lbs (alternator bolt). Oil filter housing bolt tightens to 10 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the engine block. The cylinder head bolt uses a 14mm drive on a M10x1.5 thread, torqued to Stage 1: 40 ft-lbs, Stage 2: +90° at the engine. At the cylinder head, the valve cover bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread). For the cylinder head, plan for a 16mm tool on a M14x1.25 stud; final torque is 13 ft-lbs (spark plug). Connecting rod bolt tightens to Stage 1: 18 ft-lbs, Stage 2: +45°, takes a 13mm driver, runs on M9x1.0 threads, located at the engine. The timing cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 10 ft-lbs at the front of engine. At the front of engine, the water pump bolt torques to 15 ft-lbs (12mm drive, M8x1.25 thread). For the oil pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 30 ft-lbs (40 Nm) (oil drain plug).

Suspension — 2020 Toyota Tundra

Suspension and chassis fastener torque for the 2020 Toyota Tundra — strut, control arm, and sway bar values. Ball joint nut tightens to 67 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the control arm. The sway bar link nut uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the sway bar. At the subframe, the lower control arm bolt torques to 85 ft-lbs (19mm drive, M14x2.0 thread). For the wheel hub, plan for a 21mm tool on a M14x1.5 stud; final torque is 97 ft-lbs (131 Nm) (wheel lug nut). Strut mount nut tightens to 47 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the strut tower.

Interior — 2020 Toyota Tundra

Interior fasteners on the 2020 Toyota Tundra. The seat belt anchor bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the b-pillar. At the floor pan, the front seat mount bolt torques to 37 ft-lbs (14mm drive, M10x1.25 thread). For the floor pan, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (center console bolt). Door hinge bolt tightens to 27 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the door frame. The door panel clip uses a 8mm drive on a Push-Type thread, torqued to Hand Tight at the door panel.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2020 Toyota Tundra numbers above.

Loading the interactive 2020 Toyota Tundra fastener lookup with per-bolt filtering, part links, and torque tools…