2024 Toyota Tundra Lug Nut Torque & Bolt Specs

The 2024 Toyota Tundra lug nut torque is 97 ft-lbs (132 Nm), tightened with a 22mm socket on M14 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 97 ft-lbs (132 Nm) · Socket size: 22mm · Thread: M14 x 1.5.

This page is the OEM-referenced fastener summary for the 2024 Toyota Tundra. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2024 Toyota Tundra

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Toyota Tundra?

The OEM-specified lug-nut torque for the 2024 Toyota Tundra is 97 ft-lbs (132 Nm), using a 22mm socket on M14 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Toyota Tundra lug nuts?

The 2024 Toyota Tundra uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Toyota Tundra fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Tundra years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Toyota Tundra oil drain plug torque & size

→ 2024 Toyota Tundra suspension & steering torque specs (control arm, ball joint, tie rod)

All 17 2024 Toyota Tundra fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Toyota Tundra, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 17 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2024 Toyota Tundra

Wheel and lug nut spec for the 2024 Toyota Tundra. At the wheel hub, the wheel lug nut torques to 97 ft-lbs (132 Nm) (22mm drive, M14 x 1.5 thread). OEM-verified spec.

Brakes — 2024 Toyota Tundra

Brake fasteners on the 2024 Toyota Tundra — caliper bracket, slide pins, and banjo bolt torque follow. For the steering knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 133 ft-lbs (180 Nm) (caliper bracket bolt). Confirmed against manufacturer service literature. Brake rotor set screw tightens to 4 ft-lbs, takes a 5mm driver, runs on M5x0.8 threads, located at the rotor face.

Engine — 2024 Toyota Tundra

Engine bolt-by-bolt torque for the 2024 Toyota Tundra, including the long block, valve covers, and intake. Oil drain plug tightens to 30 ft-lbs (41 Nm), located at the oil pan. This figure is independently verified against OEM service data. The oil filter housing bolt uses a 10mm drive on a M6x1.0 thread, torqued to 10 ft-lbs at the engine block. At the front of engine, the timing cover bolt torques to 10 ft-lbs (10mm drive, M6x1.0 thread). For the engine, plan for a 13mm tool on a M9x1.0 stud; final torque is Stage 1: 18 ft-lbs, Stage 2: +45° (connecting rod bolt). Spark plug tightens to 15 ft-lbs (20 Nm), located at the cylinder head. OEM-verified spec. The cylinder head bolt uses a 14mm drive on a M10x1.5 thread, torqued to Stage 1: 40 ft-lbs, Stage 2: +90° at the engine. At the front of engine, the water pump bolt torques to 15 ft-lbs (12mm drive, M8x1.25 thread).

Suspension — 2024 Toyota Tundra

Suspension and chassis fastener torque for the 2024 Toyota Tundra — strut, control arm, and sway bar values. The strut mount nut uses a 14mm drive on a M10x1.25 thread, torqued to 47 ft-lbs at the strut tower. At the control arm, the ball joint nut torques to 67 ft-lbs (19mm drive, M14x2.0 thread). For the subframe, plan for a 19mm tool on a M14x2.0 stud; final torque is 85 ft-lbs (lower control arm bolt).

Interior — 2024 Toyota Tundra

Interior fasteners on the 2024 Toyota Tundra. At the b-pillar, the seat belt anchor bolt torques to 43 ft-lbs (17mm drive, M12x1.25 thread). For the floor pan, plan for a 14mm tool on a M10x1.25 stud; final torque is 37 ft-lbs (front seat mount bolt). Door panel clip tightens to Hand Tight, takes a 8mm driver, runs on Push-Type threads, located at the door panel. The door hinge bolt uses a 12mm drive on a M8x1.25 thread, torqued to 27 ft-lbs at the door frame.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Toyota Tundra numbers above.

Loading the interactive 2024 Toyota Tundra fastener lookup with per-bolt filtering, part links, and torque tools…