2017 Chevrolet Equinox Bolt Sizes & Torque Specs
Lug nut torque is not verified for this summary. Review the cited evidence and exact hardware application before installation.
Where these numbers come from
1 value for the 2017 Chevrolet Equinox is checked against a maker’s document. Each row names the document, the page or section and the manual’s own wording, so you can check it yourself.
| Spec | Value | Document and page | Manual wording | Applies to |
|---|---|---|---|---|
| Valve Cover Bolt — torque | 89 in-lbs (10 Nm) | GM-attributed 2017 Chevrolet Equinox service information mirror (LEMON Manuals): Engine Mechanical - 2.4L, Camshaft Cover Replacement (on vehicle), callout 1; Fastener Specifications table · lemon-manuals.la | “Camshaft Cover Fastener (Qty: 11) ... Tighten 10 N.m (89 lb in) | Spec table: Camshaft Cover Bolt | 10 N.m (89 lb in)” | Original GM camshaft cover bolts, every engine offered for the 2017 Equinox: 2.4L cover (11 bolts, no tightening order printed) and 3.6L V6 covers (13 right + 15 left, GM's numbered on-vehicle sequence: "Tighten the left camshaft cover bolts in the sequence shown to 10 N.m (89 lb in)."). New cover gasket; new grommets per GM. Not aftermarket covers. Applies to: 2.4L L4 / 3.6L V6: LS, LT, LTZ (3 configurations). |
Tools for this job
Matched to the specs on this page.
As an Amazon Associate I earn from qualifying purchases. Tool picks are general options, not a fit guarantee for your vehicle or fastener.
- 1/2" Drive Click Torque Wrench (10–150 ft-lb)Lug nuts: Check its range includes your spec before ordering.EPAuto 1/2" Drive Click Torque Wrench, 10–150 ft-lb — view on Amazon
- Lug Nut Socket Set (17/19/21/22 mm)Lug nuts: Wheel-protective sleeves. Measure your lug nut first; this set covers 17, 19, 21 and 22 mm.MIXPOWER 1/2"-Drive Wheel Protector Thin-Wall Deep Lug Socket Set (4-pc) — view on Amazon
Every value on this page for the 2017 Chevrolet Equinox names the document it was checked against. Match the exact hardware and manual conditions before maintenance. A source for one field does not verify the other specifications.
Working on the 2017 Chevrolet Equinox: What You Need to Know
Second generation (2010–2017)
The 2017 Equinox's second generation (2010–2017) is built on GM's Theta platform, with a 182-hp 2.4-liter Ecotec four-cylinder and, from 2013, an available 301-hp 3.6-liter V6.
Note that 2010–2013 2.4-liter cars are widely documented for high oil consumption tied to piston-ring wear, later covered by a GM settlement.
Frequently asked questions
Are the 2017 Chevrolet Equinox fasteners metric or SAE?
Metric and SAE hardware can both appear on one vehicle, depending on the component and exact application. Use the individually verified field and the actual fastener or service manual rather than inferring a standard from the model year, make or generation. Bolt-head markings can help identify the hardware at the bench.
Not yet verified for the 2017 Chevrolet Equinox: lug nut torque and lug nut socket size. Check your owner’s or service manual, or ask a dealer. Send a correction
Other Chevrolet Equinox years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
- 2025 Chevrolet Equinox lug nut torque
- 2024 Chevrolet Equinox lug nut torque
- 2023 Chevrolet Equinox lug nut torque
- 2022 Chevrolet Equinox lug nut torque
- 2021 Chevrolet Equinox lug nut torque
- 2020 Chevrolet Equinox lug nut torque
- 2019 Chevrolet Equinox lug nut torque
- 2018 Chevrolet Equinox lug nut torque
- 2016 Chevrolet Equinox lug nut torque
- 2015 Chevrolet Equinox lug nut torque
- 2014 Chevrolet Equinox lug nut torque
- 2013 Chevrolet Equinox lug nut torque
- 2012 Chevrolet Equinox lug nut torque
- 2011 Chevrolet Equinox lug nut torque
- 2010 Chevrolet Equinox lug nut torque
- 2009 Chevrolet Equinox lug nut torque
→ 2017 Chevrolet Equinox suspension & steering torque specs (control arm, ball joint, tie rod)
Fasteners on record for the 2017 Chevrolet Equinox
1 of the 9 fasteners on record for the 2017 Chevrolet Equinox has at least one value checked against a maker’s document; each sentence below names it. A checked torque does not confirm the socket size, thread or part number. Where sources disagree, the value is withheld.
Engine — 2017 Chevrolet Equinox
Engine fasteners checked against a maker’s document for the 2017 Chevrolet Equinox. Valve Cover Bolt (Camshaft (valve) cover to cylinder head). Torque: 89 in-lbs (10 Nm). Source: GM-attributed 2017 Chevrolet Equinox service information mirror (LEMON Manuals): Engine Mechanical - 2.4L, Camshaft Cover Replacement (on vehicle), callout 1; Fastener Specifications table. Original GM camshaft cover bolts, every engine offered for the 2017 Equinox: 2.4L cover (11 bolts, no tightening order printed) and 3.6L V6 covers (13 right + 15 left, GM's numbered on-vehicle sequence: "Tighten the left camshaft cover bolts in the sequence shown to 10 N.m (89 lb in)."). New cover gasket; new grommets per GM. Not aftermarket covers. engine: 2.4L L4 / 3.6L V6; trim: LT
Also on record but not yet checked against a maker’s document (8): Front Brake Caliper Bracket Bolt, Front Brake Caliper Slide Pin, Front Hub/Bearing Nut, Lug Nut, Oil Drain Plug, Spark Plug, Sway Bar End Link Nut, Tie Rod End Nut. Their stored figures are not shown until a document confirms them. Have the factory figure? Send a correction.
Valve cover fastener locations and tightening sequence — 2017 Chevrolet Equinox
2.4L 4-cylinder: 89 in-lbs (10 Nm)
- 11 cover bolts, all tightened to the same torque. Each is held in the cover by a retainer, so the bolts lift off with the cover and go back into the same holes.
- GM gives no tightening order: start every bolt by hand, then tighten each one to 89 in-lbs (10 Nm).
- Fit a new cover gasket and new cover grommets (and new bolts, if your bolts come with the grommet).
- Move the ignition-coil harness clips and the fuel line bracket over to the cover.
Other fasteners on this cover (studs, coil and bracket bolts):
- Ignition coil bolts, one per coil (4): 89 in-lbs (10 Nm)
- Camshaft housing cover insulator bolts: 89 in-lbs (10 Nm)
- Ball studs that the plastic engine cover snaps onto (no torque printed)
Source: GM service information (2010–2017 Terrain and Equinox, 2.4L): Camshaft Cover Replacement, Camshaft Cover Installation, Fastener Specifications.
3.6L V6 (LFX): 89 in-lbs (10 Nm)
- Two covers: the right cover (bank 1) has 13 bolts, the left cover (bank 2, with the oil-fill cap) has 15.
- Fit new bolt grommets, then start every bolt by hand.
- Tighten in the numbered order to 89 in-lbs (10 Nm). This is GM's engine-in-car order; GM's engine-out procedure numbers the right cover differently.
- Put an 8 mm wide, 4 mm high bead of RTV sealant on the engine front cover split lines before setting each cover down.
Other fasteners on this cover (studs, coil and bracket bolts):
- Ball stud on the left cover for the plastic fuel-injector cover: 89 in-lbs (10 Nm)
Source: GM service information (2013–2017 Terrain and Equinox, 2012–2017 Impala, 3.6L): Camshaft Cover Replacement, Left Side and Right Side.
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then compare any source-backed fields on this page with the actual hardware and service manual.
Loading the interactive 2017 Chevrolet Equinox fastener lookup with per-bolt filtering, part links, and torque tools…