2002 Ford Fiesta Lug Nut Torque & Bolt Specs

The 2002 Ford Fiesta lug nut torque is 95 ft-lbs (129 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 95 ft-lbs (129 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2002 Ford Fiesta. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2002 Ford Fiesta

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2002 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2002 Ford Fiesta?

The OEM-specified lug-nut torque for the 2002 Ford Fiesta is 95 ft-lbs (129 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2002 Ford Fiesta lug nuts?

The 2002 Ford Fiesta uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2002 Ford Fiesta fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Fiesta years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2002 Ford Fiesta oil drain plug torque & size

→ 2002 Ford Fiesta suspension & steering torque specs (control arm, ball joint, tie rod)

All 12 2002 Ford Fiesta fastener specs

Per-bolt torque, wrench size, and thread spec for the 2002 Ford Fiesta, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2002 Ford Fiesta

Brake fasteners on the 2002 Ford Fiesta — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper carrier bolt uses a 18mm drive on a M12x1.5 thread, torqued to 115 Nm (85 lb-ft) at the carrier to knuckle. At the caliper to carrier, the front brake caliper bolt torques to 30 Nm (22 lb-ft) (13mm drive, M10x1.5 thread). For the wheel hub, plan for a 19mm tool on a M12x1.5 stud; final torque is 95 ft-lbs (129 Nm) (wheel lug nut).

Engine — 2002 Ford Fiesta

Engine bolt-by-bolt torque for the 2002 Ford Fiesta, including the long block, valve covers, and intake. At the oil pan, the oil drain plug torques to 25 Nm (18 lb-ft) (13mm drive, M14x1.5 thread). For the cylinder head, plan for a 16mm tool on a M14x1.25 stud; final torque is 15 Nm (11 lb-ft) (spark plug). Valve cover bolt tightens to 7 Nm (62 lb-in), takes a 8mm driver, runs on M6x1.0 threads, located at the valve cover.

Suspension — 2002 Ford Fiesta

Suspension and chassis fastener torque for the 2002 Ford Fiesta — strut, control arm, and sway bar values. For the lower shock mount to axle, plan for a 15mm tool on a M10x1.5 stud; final torque is 48 Nm (35 lb-ft) (rear shock absorber lower bolt). Rear shock absorber upper bolt tightens to 25 Nm (18 lb-ft), takes a 13mm driver, runs on M8x1.25 threads, located at the upper shock mount. The front strut to knuckle bolt uses a 15mm drive on a M12x1.5 thread, torqued to 80 Nm (59 lb-ft) at the strut pinch bolt. At the top of strut tower, the front strut top mount nut torques to 30 Nm (22 lb-ft) (18mm drive, M10x1.5 thread). For the end link to strut/sway bar, plan for a 15mm tool on a M10x1.5 stud; final torque is 48 Nm (35 lb-ft) (sway bar end link nut).

Steering — 2002 Ford Fiesta

Steering linkage fasteners on the 2002 Ford Fiesta. Tie rod end nut tightens to 48 Nm (35 lb-ft), takes a 17mm driver, runs on M12x1.75 threads, located at the tie rod to steering knuckle.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2002 Ford Fiesta numbers above.

Loading the interactive 2002 Ford Fiesta fastener lookup with per-bolt filtering, part links, and torque tools…