2016–2017 Ford Fiesta Lug Nut Torque & Bolt Specs

The 2017 Ford Fiesta lug nut torque is 100 ft-lbs (135 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2017 Ford Fiesta. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

These specifications also apply to the 2016 model years — identical specs on file for each year.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2017 Ford Fiesta

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2017 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2017 Ford Fiesta?

The OEM-specified lug-nut torque for the 2017 Ford Fiesta is 100 ft-lbs (135 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2017 Ford Fiesta lug nuts?

The 2017 Ford Fiesta uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2017 Ford Fiesta fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Fiesta years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2017 Ford Fiesta oil drain plug torque & size

→ 2017 Ford Fiesta suspension & steering torque specs (control arm, ball joint, tie rod)

All 19 2017 Ford Fiesta fastener specs

Per-bolt torque, wrench size, and thread spec for the 2017 Ford Fiesta, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2017 Ford Fiesta

Brake fasteners on the 2017 Ford Fiesta — caliper bracket, slide pins, and banjo bolt torque follow. For the caliper to knuckle, plan for a 15mm tool on a M12x1.75 stud; final torque is 115 Nm (85 lb-ft) (front brake caliper bolt). Rear brake drum screw tightens to 10 Nm (89 lb-in), takes a T30 Torx driver, runs on M6x1.0 threads, located at the securing drum to hub. The wheel lug nut uses a 19mm drive on a M12x1.5 thread, torqued to 100 ft-lbs (135 Nm) at the wheel hub.

Engine — 2017 Ford Fiesta

Engine bolt-by-bolt torque for the 2017 Ford Fiesta, including the long block, valve covers, and intake. Crankshaft pulley bolt tightens to 100 Nm + 90 degrees, takes a 18mm driver, runs on M12x1.5 threads, located at the crankshaft. The oil drain plug uses a 15mm drive on a M12x1.75 thread, torqued to 28 Nm (21 lb-ft) at the oil pan. At the exhaust manifold to head, the exhaust manifold nut torques to 16 Nm (12 lb-ft) (13mm drive, M8x1.25 thread). For the valve cover, plan for a 8mm tool on a M6x1.0 stud; final torque is 10 Nm (89 lb-in) (valve cover bolt). Turbocharger to manifold nut tightens to 25 Nm (18 lb-ft), takes a 13mm driver, runs on M8x1.25 threads, located at the turbo to exhaust manifold. The intake manifold bolt uses a 10mm drive on a M8x1.25 thread, torqued to 18 Nm (13 lb-ft) at the intake manifold to head. At the cylinder head, the spark plug torques to 12 Nm (9 lb-ft) (16mm drive, M12x1.25 thread).

Suspension — 2017 Ford Fiesta

Suspension and chassis fastener torque for the 2017 Ford Fiesta — strut, control arm, and sway bar values. The sway bar end link nut uses a 15mm drive on a M10x1.5 thread, torqued to 48 Nm (35 lb-ft) at the end link to strut/sway bar. At the upper shock mount, the rear shock absorber upper bolt torques to 48 Nm (35 lb-ft) (15mm drive, M10x1.5 thread). For the strut to steering knuckle, plan for a 18mm tool on a M12x1.5 stud; final torque is 90 Nm + 45 degrees (front strut to knuckle bolt). Rear shock absorber lower bolt tightens to 120 Nm (89 lb-ft), takes a 18mm driver, runs on M12x1.75 threads, located at the lower shock mount to axle. The front strut top mount nut uses a 21mm drive on a M14x1.5 thread, torqued to 48 Nm (35 lb-ft) at the top of strut tower.

Steering — 2017 Ford Fiesta

Steering linkage fasteners on the 2017 Ford Fiesta. At the tie rod to steering knuckle, the tie rod end nut torques to 48 Nm (35 lb-ft) (18mm drive, M12x1.75 thread).

Exhaust — 2017 Ford Fiesta

Exhaust fasteners on the 2017 Ford Fiesta. For the downpipe v-band, plan for a 15mm tool on a M10x1.5 stud; final torque is 18 Nm (13 lb-ft) (downpipe to turbo nut).

Cooling System — 2017 Ford Fiesta

Cooling System fasteners on the 2017 Ford Fiesta. Water pump bolt tightens to 20 Nm (15 lb-ft), takes a 10mm driver, runs on M8x1.25 threads, located at the water pump to block. The thermostat housing bolt uses a 8mm drive on a M6x1.0 thread, torqued to 10 Nm (89 lb-in) at the thermostat housing.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2017 Ford Fiesta numbers above.

Loading the interactive 2017 Ford Fiesta fastener lookup with per-bolt filtering, part links, and torque tools…