2013 Kia Sedona Lug Nut Torque & Bolt Specs

The 2013 Kia Sedona lug nut torque is 80 ft-lbs (108 Nm) on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2013 Kia Sedona. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2013 Kia Sedona

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2013 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2013 Kia Sedona?

The OEM-specified lug-nut torque for the 2013 Kia Sedona is 80 ft-lbs (108 Nm) on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2013 Kia Sedona lug nuts?

Most modern Kia vehicles use a 19mm or 21mm socket. Older Kia models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2013 Kia Sedona fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia Sedona years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2013 Kia Sedona oil drain plug torque & size

→ 2013 Kia Sedona suspension & steering torque specs (control arm, ball joint, tie rod)

→ 2013 Kia Sedona axle nut torque spec (CV axle & hub nut)

All 36 2013 Kia Sedona fastener specs

Per-bolt torque, wrench size, and thread spec for the 2013 Kia Sedona, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 36 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2013 Kia Sedona

Wheel and lug nut spec for the 2013 Kia Sedona. The lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 87 ft-lbs at the wheel hub.

Brakes — 2013 Kia Sedona

Brake fasteners on the 2013 Kia Sedona — caliper bracket, slide pins, and banjo bolt torque follow. At the caliper slide, the rear slide pin torques to 20 ft-lbs (14mm drive, M10x1.25 thread). For the caliper bracket, plan for a 17mm tool on a M12x1.5 stud; final torque is 58 ft-lbs (rear caliper bracket). Front slide pin tightens to 22 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the caliper slide. The front caliper bracket bolt uses a 19mm drive on a M14x1.5 thread, torqued to 73 ft-lbs at the caliper bracket.

Engine — 2013 Kia Sedona

Engine bolt-by-bolt torque for the 2013 Kia Sedona, including the long block, valve covers, and intake. plan for the right driver on a M6x1.0 stud; final torque is 7-10 ft-lbs (valve cover bolt). Alternator mounting bolt tightens to 30-40 ft-lbs, runs on M10x1.25 threads. The oil drain plug is a M14x1.5 thread, torqued to 25 ft-lbs (34 Nm). At the exhaust manifold, the exhaust manifold torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the intake manifold, plan for a 12mm tool on a M8x1.25 stud; final torque is 18 ft-lbs (intake manifold). Oil pan drain plug tightens to 29 ft-lbs, takes a 17mm driver, runs on M14x1.5 threads, located at the oil pan. The spark plug is a M14x1.25 thread, torqued to 13-17 ft-lbs. At the valve cover, the valve cover torques to 7 ft-lbs (10mm drive, M6x1.0 thread).

Drivetrain — 2013 Kia Sedona

Drivetrain and driveline fasteners for the 2013 Kia Sedona — axle, transmission, and differential plugs. Transmission mount bolt tightens to 55-70 ft-lbs, runs on M12x1.25 threads. The axle nut front is a M24x1.5 thread, torqued to 170-200 ft-lbs. The axle nut rear torques to 170-200 ft-lbs (M24x1.5 thread).

Suspension — 2013 Kia Sedona

Suspension and chassis fastener torque for the 2013 Kia Sedona — strut, control arm, and sway bar values. The control arm uses a 19mm drive on a M14x1.5 thread, torqued to 59 ft-lbs at the control arm. The rear shock absorber upper nut torques to 35-45 ft-lbs (M12x1.25 thread). plan for the right driver on a M10x1.25 stud; final torque is 25-35 ft-lbs (stabilizer bar link nut front). Ball joint tightens to 59 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the ball joint. The sway bar link uses a 14mm drive on a M10x1.25 thread, torqued to 37 ft-lbs at the sway bar link. At the strut top mount, the front strut mount torques to 40 ft-lbs (17mm drive, M12x1.5 thread). plan for the right driver on a M14x1.5 stud; final torque is 85-100 ft-lbs (rear shock absorber lower bolt). Front lower control arm rear bolt tightens to 70-85 ft-lbs, runs on M12x1.25 threads. The front lower control arm front bolt is a M12x1.25 thread, torqued to 70-85 ft-lbs. The front strut top mount nut torques to 30-40 ft-lbs (M14x1.5 thread).

Steering — 2013 Kia Sedona

Steering linkage fasteners on the 2013 Kia Sedona. The tie rod end nut torques to 25-33 ft-lbs (M12x1.25 thread). plan for the right driver on a M10x1.25 stud; final torque is 22-30 ft-lbs (power steering pump bolt). Steering wheel center bolt tightens to 30-38 ft-lbs, runs on M16x1.5 threads.

Body — 2013 Kia Sedona

Body fasteners on the 2013 Kia Sedona. plan for the right driver on a M8x1.25 stud; final torque is 15-20 ft-lbs (hood hinge bolt).

Brake — 2013 Kia Sedona

Brake fasteners on the 2013 Kia Sedona. Front brake caliper guide pin bolt tightens to 22-30 ft-lbs, runs on M10x1.25 threads. OEM-verified spec. The front brake caliper bracket bolt is a M12x1.25 thread, torqued to 55-70 ft-lbs. The rear brake caliper bracket bolt torques to 50-65 ft-lbs (M12x1.25 thread). plan for the right driver on a M10x1.25 stud; final torque is 20-28 ft-lbs (rear brake caliper guide pin bolt). OEM-verified spec.

Wheel — 2013 Kia Sedona

Wheel fasteners on the 2013 Kia Sedona. The wheel lug nuts is a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm).

Transmission — 2013 Kia Sedona

Transmission fasteners on the 2013 Kia Sedona. At the transmission mount, the trans mount torques to 58 ft-lbs (17mm drive, M12x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2013 Kia Sedona numbers above.

Loading the interactive 2013 Kia Sedona fastener lookup with per-bolt filtering, part links, and torque tools…