2004 Nissan Altima Lug Nut Torque & Bolt Specs

The 2004 Nissan Altima lug nut torque is 80 ft-lbs (108 Nm), tightened with a Hex socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: Hex · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2004 Nissan Altima. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2004 Nissan Altima

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2004 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2004 Nissan Altima?

The OEM-specified lug-nut torque for the 2004 Nissan Altima is 80 ft-lbs (108 Nm), using a Hex socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2004 Nissan Altima lug nuts?

The 2004 Nissan Altima uses a Hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2004 Nissan Altima fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Altima years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2004 Nissan Altima oil drain plug torque & size

→ 2004 Nissan Altima suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2004 Nissan Altima fastener specs

Per-bolt torque, wrench size, and thread spec for the 2004 Nissan Altima, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 10 of the 20 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2004 Nissan Altima

Wheel and lug nut spec for the 2004 Nissan Altima. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (Hex drive, M12x1.25 thread).

Brakes — 2004 Nissan Altima

Brake fasteners on the 2004 Nissan Altima — caliper bracket, slide pins, and banjo bolt torque follow. For the brake caliper slide pin, plan for a Hex tool on a M10x1.25 stud; final torque is 16-23 ft-lbs (22-31 Nm) (brake caliper pin bolt). Confirmed against manufacturer service literature. Brake caliper mounting bolt tightens to 53-72 ft-lbs (72-97 Nm), takes a Hex driver, runs on M14x1.5 threads, located at the front/rear brake caliper. This figure is independently verified against OEM service data. The caliper bracket bolt uses a M14 drive on a M14x1.5 thread, torqued to 110-130 Nm at the front brakes.

Engine — 2004 Nissan Altima

Engine bolt-by-bolt torque for the 2004 Nissan Altima, including the long block, valve covers, and intake. Oil filter tightens to Hand tight (18 Nm), takes a Canister driver, runs on M20x1.5 threads, located at the engine block. This figure is independently verified against OEM service data. The oil drain plug uses a 14mm drive on a M12x1.25 thread, torqued to 25 ft-lbs (34 Nm) at the oil pan. At the oil pan - lower, the oil pan bolt (8mm) torques to 6-7 ft-lbs (8-10 Nm) (Hex drive, M8x1.25 thread). Confirmed against manufacturer service literature. For the oil pan - upper, plan for a Hex tool on a M10x1.25 stud; final torque is 12-17 ft-lbs (16-24 Nm) (oil pan bolt (10mm)). This figure is independently verified against OEM service data. Valve cover bolt tightens to Step1 1-3 Nm then Step2 7.4-9.3 Nm (65-82 in-lbs), takes a Hex driver, runs on M8x1.25 threads, located at the valve cover. OEM-verified spec. The intake manifold bolt uses a Hex drive on a M10x1.25 thread, torqued to 13-15 ft-lbs (18-22 Nm) I4 at the intake manifold. Confirmed against manufacturer service literature.

Drivetrain — 2004 Nissan Altima

Drivetrain and driveline fasteners for the 2004 Nissan Altima — axle, transmission, and differential plugs. The axle nut uses a 32mm drive on a Special thread, torqued to 250-280 Nm at the wheel hub.

Suspension — 2004 Nissan Altima

Suspension and chassis fastener torque for the 2004 Nissan Altima — strut, control arm, and sway bar values. At the rear shock mount, the rear shock upper bolt torques to 20-24 ft-lbs (27-33 Nm) (Hex drive, M12x1.25 thread). Confirmed against manufacturer service literature. For the front suspension, plan for a M14 tool on a M14 x 1.5 stud; final torque is 130-150 Nm (strut to knuckle bolt). Front strut lower bolt tightens to 93-114 ft-lbs (126-155 Nm), takes a Hex driver, runs on M14x1.5 threads, located at the strut to knuckle. OEM-verified spec. The lower control arm bolt uses a 19mm drive on a M14x1.5 thread, torqued to 85-94 ft-lbs at the front suspension.

General — 2004 Nissan Altima

General fasteners on the 2004 Nissan Altima. For the rear axle, plan for a Hex tool on a M14x1.5 stud; final torque is 74-88 ft-lbs (101-119 Nm) (rear shock lower bolt). This figure is independently verified against OEM service data. Spark plug tightens to 14 ft-lbs (19 Nm), takes a Hex driver, runs on M12x1.25 threads, located at the cylinder head.

Transmission — 2004 Nissan Altima

Transmission fasteners on the 2004 Nissan Altima. Transmission drain plug tightens to 22-29 ft-lbs (30-39 Nm) 4-speed automatic (I4), takes a Hex driver, runs on M14x1.5 threads, located at the transmission pan.

Wheels & Tires — 2004 Nissan Altima

Wheels & Tires fasteners on the 2004 Nissan Altima. The lug nut uses a 21mm drive on a M12x1.25 thread, torqued to 80 ft-lbs (108 Nm) at the wheel hub.

Exterior — 2004 Nissan Altima

Exterior fasteners on the 2004 Nissan Altima. At the wheel well, the front bumper cover screw torques to 5-7 Nm (10mm drive, M6 x 1.0 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2004 Nissan Altima numbers above.

Loading the interactive 2004 Nissan Altima fastener lookup with per-bolt filtering, part links, and torque tools…