2008 Nissan Altima Lug Nut Torque & Bolt Specs

The 2008 Nissan Altima lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2008 Nissan Altima. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2008 Nissan Altima

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2008 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2008 Nissan Altima?

The OEM-specified lug-nut torque for the 2008 Nissan Altima is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2008 Nissan Altima lug nuts?

The 2008 Nissan Altima uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2008 Nissan Altima fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Altima years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2008 Nissan Altima oil drain plug torque & size

→ 2008 Nissan Altima suspension & steering torque specs (control arm, ball joint, tie rod)

All 17 2008 Nissan Altima fastener specs

Per-bolt torque, wrench size, and thread spec for the 2008 Nissan Altima, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 12 of the 17 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed July 2026).

Wheels — 2008 Nissan Altima

Wheel and lug nut spec for the 2008 Nissan Altima. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (Hex drive, M12x1.25 thread).

Brakes — 2008 Nissan Altima

Brake fasteners on the 2008 Nissan Altima — caliper bracket, slide pins, and banjo bolt torque follow. For the front/rear brake caliper, plan for a 22mm tool on a M14x1.5 stud; final torque is 98 ft-lbs (133 Nm) (brake caliper mounting bolt). Confirmed against manufacturer service literature. Brake caliper bolt tightens to 32-36 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the front brake caliper. The brake caliper pin bolt uses a Hex drive on a M10x1.25 thread, torqued to 20 ft-lbs (27 Nm) at the brake caliper slide pin. OEM-verified spec.

Engine — 2008 Nissan Altima

Engine bolt-by-bolt torque for the 2008 Nissan Altima, including the long block, valve covers, and intake. Oil drain plug tightens to 25 ft-lbs (34 Nm), takes a 14mm driver, runs on M12x1.25 threads, located at the oil pan. This figure is independently verified against OEM service data. The intake manifold bolt uses a Hex drive on a M10x1.25 thread, torqued to 14 ft-lbs (20 Nm) I4 at the intake manifold. OEM-verified spec. At the valve cover, the valve cover bolt torques to Step1 2 Nm then Step2 8.3 Nm (74 in-lbs) (Hex drive, M8x1.25 thread). Confirmed against manufacturer service literature. For the engine block, plan for a Canister tool on a M20x1.5 stud; final torque is Hand tight (18 Nm) (oil filter). This figure is independently verified against OEM service data. Oil pan bolt (8mm) tightens to 5 ft-lbs (7 Nm), takes a Hex driver, runs on M8x1.25 threads, located at the oil pan - lower. OEM-verified spec. The oil pan bolt (10mm) uses a Hex drive on a M10x1.25 thread, torqued to 16 ft-lbs (22 Nm) upper pan at the oil pan - upper. Confirmed against manufacturer service literature.

Suspension — 2008 Nissan Altima

Suspension and chassis fastener torque for the 2008 Nissan Altima — strut, control arm, and sway bar values. The front strut lower bolt uses a Hex drive on a M14x1.5 thread, torqued to 103 ft-lbs (140 Nm) at the strut to knuckle. OEM-verified spec. At the front suspension, the lower control arm bolt torques to 85-94 ft-lbs (19mm drive, M14x1.5 thread). For the rear shock mount, plan for a Hex tool on a M12x1.25 stud; final torque is 22 ft-lbs (30 Nm) (rear shock upper bolt). This figure is independently verified against OEM service data.

General — 2008 Nissan Altima

General fasteners on the 2008 Nissan Altima. At the cylinder head, the spark plug torques to 14 ft-lbs (19 Nm) (Hex drive, M12x1.25 thread). For the rear axle, plan for a Hex tool on a M14x1.5 stud; final torque is 66 ft-lbs (90 Nm) (rear shock lower bolt). This figure is independently verified against OEM service data.

Wheels & Tires — 2008 Nissan Altima

Wheels & Tires fasteners on the 2008 Nissan Altima. For the wheel hub, plan for a 21mm tool on a M12x1.25 stud; final torque is 80 ft-lbs (108 Nm) (lug nut).

Transmission — 2008 Nissan Altima

Transmission fasteners on the 2008 Nissan Altima. Transmission drain plug tightens to 25 ft-lbs (34 Nm) CVT RE0F10A (I4), takes a Hex driver, runs on M14x1.5 threads, located at the transmission pan. OEM-verified spec.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2008 Nissan Altima numbers above.

Loading the interactive 2008 Nissan Altima fastener lookup with per-bolt filtering, part links, and torque tools…