2002 Toyota Tacoma Lug Nut Torque & Bolt Specs

The 2002 Toyota Tacoma lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2002 Toyota Tacoma. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2002 Toyota Tacoma

Repair guidance for this model year

For 2002 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Frequently asked questions

What is the lug nut torque on a 2002 Toyota Tacoma?

The OEM-specified lug-nut torque for the 2002 Toyota Tacoma is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2002 Toyota Tacoma lug nuts?

The 2002 Toyota Tacoma uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2002 Toyota Tacoma fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Tacoma years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2002 Toyota Tacoma oil drain plug torque & size

→ 2002 Toyota Tacoma suspension & steering torque specs (control arm, ball joint, tie rod)

All 80 2002 Toyota Tacoma fastener specs

Per-bolt torque, wrench size, and thread spec for the 2002 Toyota Tacoma, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 80 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2002 Toyota Tacoma

Wheel and lug nut spec for the 2002 Toyota Tacoma. The lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm) at the all four wheels.

Brakes — 2002 Toyota Tacoma

Brake fasteners on the 2002 Toyota Tacoma — caliper bracket, slide pins, and banjo bolt torque follow. At the see also suspension section. both front and rear abs sensors = 71 in-lbs., the abs wheel speed sensor bolt (brake system) torques to 71 in-lbs (5.9 ft-lbs) ft-lbs (8 Nm) (10mm drive, M6 thread). For the gen1 2wd front caliper mounting bolts. gen1 4wd: 90 ft-lbs (123 nm)., plan for a 17mm tool on a M14 stud; final torque is 90 ft-lbs (123 Nm) (front brake caliper bracket bolts (caliper x steering knuckle) — gen1). Confirmed against manufacturer service literature. Brake caliper bracket bolt tightens to 90 ft-lbs (123 Nm), takes a 17mm driver, runs on M12x1.25 threads, located at the steering knuckle. This figure is independently verified against OEM service data. The wheel lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 76 ft-lbs at the wheel hub. At the all brake line fittings (flare nut). use flare wrench to prevent rounding. do not use open-end wrench., the brake line union nut torques to 11 ft-lbs (15 Nm) (10mm flare wrench drive, 3/8" flare nut thread). For the backing plate (dust shield) bolt torque for drum brake rear axles. gen1 fsm: 50 ft-lbs (68 nm)., plan for a 14mm tool on a M12 stud; final torque is 48 ft-lbs (68 Nm) (rear drum brake backing plate x axle housing). Brake caliper bolt tightens to 65 ft-lbs (88 Nm), takes a 14mm driver, runs on M12x1.25 threads, located at the caliper bracket. OEM-verified spec. The front caliper slide pin bolts uses a 12mm or 14mm depending on year drive on a M10 thread, torqued to 65 ft-lbs (88 Nm) at the sliding guide pin bolts (the smaller bolts, not the bracket bolts). apply caliper grease/silicone lube to guide pins before installation.. Confirmed against manufacturer service literature.

Engine — 2002 Toyota Tacoma

Engine bolt-by-bolt torque for the 2002 Toyota Tacoma, including the long block, valve covers, and intake. For the located at front of engine on the intake side. use new o-ring or gasket., plan for a 12mm tool on a M8 stud; final torque is 14 ft-lbs (19 Nm) (thermostat housing (water inlet) bolts). Connecting rod bolt tightens to Stage 1: 18 ft-lbs, Stage 2: +45°, takes a 13mm driver, runs on M9x1.0 threads, located at the engine. The camshaft bearing cap bolts (cam bearing cap x cylinder head) uses a 12mm drive on a 8mm thread, torqued to 12 ft-lbs (16 Nm) at the tighten uniformly in several passes in specified sequence (from center outward). 5 bearing caps per bank (10 total). critical: follow toyota tightening sequence.. At the engine block, the oil filter housing cap torques to 25 ft-lbs (64mm drive, M64x1.5 thread). For the 3 nuts per manifold, 6 per engine (plus crossover pipe nuts at 33 ft-lbs). use anti-seize on studs. tighten from center outward., plan for a 14mm nut, E8 Torx stud tool on a M10 stud; final torque is 30 ft-lbs (40 Nm) (exhaust manifold nuts x cylinder head). Camshaft timing pulley x camshaft tightens to 81 ft-lbs (110 Nm), takes a 17mm driver, runs on M10 threads, located at the hold cam with wrench while torquing. this is the cam sprocket bolt at the front of each camshaft.. The cylinder head bolts — recessed head (short bolts) uses a 12mm drive on a M8 thread, torqued to 13 ft-lbs (18 Nm) at the these are the smaller head bolts (not angle-method). final torque only, no angle turn. typically 2 per head at front/rear positions.. At the also applies to intake manifold stay bolts. air intake chamber x intake air connector = 13 ft-lbs. air intake chamber stay to lh cylinder head = 30 ft-lbs., the intake manifold x cylinder head torques to 13 ft-lbs (18 Nm) (12mm drive, M8 thread). For the also: water inlet x water pump = 14 ft-lbs. use new gasket and rtv sealant as appropriate., plan for a 12mm tool on a M8 stud; final torque is 14 ft-lbs (19 Nm) (water pump x cylinder block). Connecting rod bolts (connecting rod cap x connecting rod) tightens to Step 1: 18 ft-lbs | Step 2: +90° ft-lbs (Step 1: 25 Nm Nm), takes a 12mm driver, runs on M9 threads, located at the tty angle method. replace rod bolts if removed. apply light engine oil to threads and under bolt head before installation.. The main bearing cap bolts (main bearing cap x cylinder block) uses a 14mm drive on a M11 thread, torqued to Step 1: 45 ft-lbs | Step 2: +90° ft-lbs (Step 1: 61 Nm Nm) at the tty angle method. after tightening, verify crankshaft rotates smoothly by hand. 4 main bearing caps on this engine.. At the use loctite. apply in star pattern. drive plate (a/t flexplate) = 61 ft-lbs., the flywheel x crankshaft (mt) torques to 63 ft-lbs (85 Nm) (14mm drive, M12 thread). For the use new crush washer each oil change. the fsm cites the drain cock at 29 ft-lbs (engine coolant drain cock). typical oem drain plug = 29 ft-lbs. do not overtighten., plan for a 14mm tool on a M14 x 1.5 stud; final torque is Not specified separately in FSM — use 29 ft-lbs ft-lbs (39 Nm) (oil drain plug). Spark plug tightens to 13 ft-lbs (18 Nm), takes a 5/8" (16mm) spark plug socket driver, runs on 14mm x 1.25 threads, located at the 6 plugs total, 3 per bank. use anti-seize on aluminum head threads. access via valve covers.. The 2rz-fe cylinder head bolts uses a 12mm 12-point drive on a M11 thread, torqued to Step 1: 25 ft-lbs | Step 2: +90° | Step 3: +90° ft-lbs (Step 1: 34 Nm Nm) at the tty 3-pass method. recessed bolts: 13 ft-lbs.. At the critical: angle torque (tty) method. use new bolts if reusing — inspect for stretch. tighten in sequence per fsm (outside-in to center pattern). 3-pass method: 25 ft-lbs, then 90°, then another 90°. recessed head bolts (shorter bolts): 13 ft-lbs only — no angle method., the cylinder head bolts — 12-point head (main bolts) torques to Step 1: 25 ft-lbs | Step 2: +90° | Step 3: +90° ft-lbs (Step 1: 34 Nm Nm) (12mm 12-point socket drive, M11 (12-point head) thread). For the right-hand (rh) engine mount bracket to block. left-hand uses same spec., plan for a 14mm tool on a M12 stud; final torque is 32 ft-lbs (44 Nm) (engine mount bracket x cylinder block). Crankshaft pulley bolt (harmonic balancer) tightens to 184 ft-lbs (250 Nm), takes a 19mm hex or 1-1/4" socket (use breaker bar or impact) driver, runs on M20 x 1.5 (right-hand thread) threads, located at the critical: one of the most searched specs. oem service manual value is 184 ft-lbs (250 nm). some sources cite 217 ft-lbs — that value is for the camshaft timing pulley bolt, not the crank pulley. use crankshaft holding tool (sst 09213-70010 or equivalent) to prevent rotation. this is not a tty bolt.. The valve cover bolts (cylinder head cover x cylinder head) uses a 10mm drive on a 6mm thread, torqued to 53 in-lbs (4.4 ft-lbs) ft-lbs (6 Nm) at the tighten uniformly in multiple passes. do not overtighten — these strip easily in aluminum.. At the 4 bolts/nuts. same torque for models with and without etcs-i. do not overtighten., the throttle body x air intake chamber torques to 13 ft-lbs (18 Nm) (12mm drive, M8 thread). For the front mount-to-frame crossmember bolts., plan for a 14mm tool on a M12 stud; final torque is 28 ft-lbs (38 Nm) (engine front mounting insulator x frame). Timing belt tensioner x oil pump tightens to 20 ft-lbs (27 Nm), takes a 12mm driver, runs on M10 threads, located at the set belt tension before final tightening. located on front of engine at oil pump mounting boss.. The 2rz-fe spark plug uses a 5/8" spark plug socket drive on a 14mm x 1.25 thread, torqued to 14 ft-lbs (19 Nm) at the 2.4l 4-cylinder gen1 (1995-early tacoma). sohc engine.. At the cylinder head, the valve cover bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread). For the engine, plan for a 14mm tool on a M10x1.5 stud; final torque is Stage 1: 40 ft-lbs, Stage 2: +90° (cylinder head bolt). Oil pan bolts (oil pan x cylinder block) tightens to 67 in-lbs (5.6 ft-lbs) ft-lbs (7.5 Nm), takes a 10mm driver, runs on 6mm threads, located at the tighten in a crisscross pattern in multiple passes. rtv sealant required on mating surfaces. also 2 nuts at same torque..

Drivetrain — 2002 Toyota Tacoma

Drivetrain and driveline fasteners for the 2002 Toyota Tacoma — axle, transmission, and differential plugs. Front axle hub nut (drive shaft x axle hub) — 4wd tightens to 174 ft-lbs (235 Nm), takes a 35mm socket (or 1-3/8") driver, runs on M22 x 1.5 (large hex, cotter pin) threads, located at the critical: gen1 4wd front axle nut spec. use new cotter pin and lock cap. tighten, then back off and re-tighten to align cotter pin slot — do not reduce torque below spec. hold rotor to prevent rotation.. The rear ring gear x differential case uses a 14mm drive on a M12 thread, torqued to 92 ft-lbs (125 Nm) at the gen1 standard rear diff (5vz-fe/3rz-fe without diff lock). with diff lock: 71 ft-lbs. use loctite on ring gear bolts. apply in star pattern.. At the transfer case adapter/mating flange bolts. engine rear mounting to transmission = 48 ft-lbs., the transfer case x transmission (transfer to transmission) torques to 17 ft-lbs (23 Nm) (12mm drive, M10 thread). For the both no. 3 and no. 4 crossmember to frame = 53 ft-lbs. engine rear mounting to crossmember = 13 ft-lbs., plan for a 14mm tool on a M12 stud; final torque is 53 ft-lbs (72 Nm) (transmission crossmember (no. 3/4 crossmember x frame)). Front differential mounting cushion x frame (front mount) tightens to 101 ft-lbs (137 Nm), takes a 24mm driver, runs on M16 threads, located at the front diff front mount to frame. front diff front cushion to diff = 116 ft-lbs. rear mount: to frame = 64 ft-lbs; to diff = 80 ft-lbs.. The transfer case companion flange lock nut (front and rear output) uses a 32mm or equivalent drive on a M22 thread, torqued to 87 ft-lbs (118 Nm) at the both front and rear companion flanges on transfer case (vf2a and vf3am units). use holding tool.. At the critical: not a torque-to-value spec. set to achieve correct bearing preload using inch-pound torque wrench while measuring rotational resistance. consult fsm pages sa-55 (front diff) and sa-149/sa-166/sa-185 for full procedure., the rear pinion nut (drive pinion x companion flange) torques to Preload method — bearing preload: 10.4–16.5 in-lbs (starting torque). See FSM SA-149 (5VZ-FE) / SA-166 ft-lbs (N/A — preload spec Nm) (Special holding fixture required drive, M22 thread). For the rear diff drain plug and fill plug = 36 ft-lbs. gen2 rear diff cover bolts = 26 ft-lbs (35 nm). front diff drain = 48 ft-lbs (gen1), fill = 29 ft-lbs., plan for a 24mm or 3/8" square drive tool on a M18 stud; final torque is 36 ft-lbs (49 Nm) (rear differential cover bolts (drain/filler plugs)). Transmission x engine (bellhousing bolts) tightens to 53 ft-lbs (72 Nm), takes a 14mm driver, runs on M12 threads, located at the applies to a340f a/t and r150f/w59 m/t. also transmission to starter = 29 ft-lbs.. The differential cover bolt uses a 12mm drive on a M8x1.25 thread, torqued to 23 ft-lbs at the differential. At the bearing cap bolts. with diff lock: 58 ft-lbs., the differential carrier bearing cap — rear (5vz/3rz without diff lock) torques to 83 ft-lbs (113 Nm) (19mm drive, M14 thread). For the rear diff carrier-to-housing bolts (without diff lock). with diff lock: 18 ft-lbs (25 nm) — check fsm., plan for a 14mm tool on a M12 stud; final torque is 54 ft-lbs (73 Nm) (differential carrier x axle housing — rear (standard, 5vz/3rz)). Propeller / driveshaft x differential (front and rear) tightens to 54 ft-lbs (74 Nm), takes a 14mm driver, runs on M10 threads, located at the all prop shaft-to-differential and shaft-to-transfer case flange bolts = 54 ft-lbs. applies to both front and rear driveshafts on 4wd, and rear driveshaft on 2wd.. The front differential ring gear x differential case uses a 12mm drive on a M10 thread, torqued to 71 ft-lbs (97 Nm) at the gen1 front differential ring gear bolts. use loctite..

Suspension — 2002 Toyota Tacoma

Suspension and chassis fastener torque for the 2002 Toyota Tacoma — strut, control arm, and sway bar values. The upper ball joint nut (steering knuckle x upper ball joint) — gen1 4wd uses a 22mm drive on a M14 thread, torqued to 80 ft-lbs (105 Nm) at the upper suspension arm x upper ball joint (4wd): 80 ft-lbs. use cotter pin.. At the front sway bar clamp bracket bolts. gen1 4wd = 19 ft-lbs. gen2/gen3 similar range 19–22 ft-lbs., the sway bar bracket bolts (stabilizer bar bracket x frame) — gen1 2wd torques to 22 ft-lbs (29 Nm) (14mm drive, M10 thread). For the leaf spring, plan for a 19mm tool on a M14x1.5 stud; final torque is 85 ft-lbs (leaf spring u-bolt). Front shock absorber lower mount x lower control arm tightens to 101 ft-lbs (135 Nm), takes a 21mm driver, runs on M14 threads, located at the gen1 and gen2. upper mount (shock to suspension support): 22 ft-lbs (gen1 4wd). gen3 lower shock = 61 ft-lbs; upper = 14 ft-lbs (strut top nut).. The upper control arm (shaft) x frame — gen1 uses a 21mm drive on a M14 thread, torqued to 94 ft-lbs (130 Nm) at the upper suspension arm shaft to frame = 94 ft-lbs. upper suspension arm shaft to arm = 92 ft-lbs.. At the front and rear abs speed sensor bolts to steering knuckle/axle housing. also sensor wire harness clamp bolts = same spec., the abs wheel speed sensor bolt torques to 71 in-lbs (5.9 ft-lbs) ft-lbs (8 Nm) (10mm drive, M6 thread). For the 83 ft-lbs for all gen1/2/3 tacomas (1995–2023). thread size: m12 x 1.5 for all years. flat-seat washer-type lug nuts. 6-lug pattern on 4wd, 5-lug on some 2wd models. tighten in star pattern. note: gen4 (2024+) changed to m14 x 1.5 at 103.5 ft-lbs., plan for a 21mm (13/16") tool on a M12 x 1.5 stud; final torque is 83 ft-lbs (113 Nm) (lug nuts — all generations gen1/gen2/gen3). Trd strut brace bolt tightens to 29 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the strut tower. The rear leaf spring front hanger bolt x frame uses a 24mm drive on a M16 thread, torqued to 116 ft-lbs (157 Nm) at the front leaf spring eye bolt to hanger bracket. with suspension loaded at ride height.. At the 4wd/prerunner lower arm to frame. lower arm to shock absorber = 101 ft-lbs., the lower control arm x frame — gen1 4wd torques to 96 ft-lbs (130 Nm) (24mm drive, M16 thread). For the 4wd gen1. lower arm x lower ball joint (4wd): 103 ft-lbs. 2 different torques — knuckle-to-bj stud nut = 59 ft-lbs; arm-to-ball-joint bolts = 103 ft-lbs., plan for a 22mm tool on a M14 stud; final torque is 59 ft-lbs (80 Nm) (lower ball joint nut (steering knuckle x lower ball joint) — gen1 4wd/prerunner). Tie rod end to knuckle nut — gen1 4wd, gen2, gen3 tightens to 67 ft-lbs (90 Nm), takes a 22mm driver, runs on M14 threads, located at the outer tie rod nut = 67 ft-lbs. can advance up to additional 60° to align cotter pin. applies gen1 4wd (90 nm = 67 ft-lbs), gen2, and gen3.. The rear leaf spring u-bolt nuts — gen1 oem uses a 19mm deep drive on a 9/16" (OEM U-bolt size) thread, torqued to 90 ft-lbs (123 Nm) at the critical: gen1 fsm: u-bolt x spring seat = 90 ft-lbs (123 nm). tighten with vehicle on the ground at ride height. re-torque after 100 miles. cross-torque pattern (diagonally opposite).. At the both shackle pin x leaf spring and shackle pin x frame = 67 ft-lbs. gen2/gen3: 89 ft-lbs per trail-gear/adventuretaco fsm data., the rear leaf spring shackle pins torques to 67 ft-lbs (92 Nm) (22mm drive, M14 thread). For the 2wd gen1. lower arm x lower ball joint = 80 ft-lbs (110 nm)., plan for a 24mm tool on a M16 stud; final torque is 116 ft-lbs (160 Nm) (lower ball joint nut (steering knuckle x lower ball joint) — gen1 2wd). Rear shock absorber upper mount tightens to 4WD/PreRunner: 53 ft-lbs | 2WD: 19 ft-lbs ft-lbs (4WD: 71 Nm | 2WD: 26 Nm Nm), takes a 17mm (4WD) / 14mm (2WD) driver, runs on M12 (4WD) / M10 (2WD) threads, located at the gen1 upper shock mount to frame. gen2 upper mount: 18 ft-lbs. gen3 upper rear shock: 18 ft-lbs.. The torsion bar anchor bolts / torsion bar adjuster — gen1 uses a 19mm drive on a M16 adjusting bolt thread, torqued to No specific OEM torque spec found — adjust to desired ride height; typical setting 10–15mm threaded engagement ft-lbs (N/A Nm) at the gen1 2wd/4wd uses torsion bar front suspension. anchor arm bolt is an adjustment bolt for ride height — not torqued to a specific value, set to specified ride height. after adjustment, re-torque lock nut (if any) snugly. gen2 and gen3 use coil springs — torsion bar does not apply.. At the ps gear assembly to frame = 123 ft-lbs. bracket to body = 123 ft-lbs. also a set bolt + nut version = 141 ft-lbs., the steering rack (ps gear) mounting bolts torques to 123 ft-lbs (166 Nm) (19mm drive, M14 thread). For the castle nut — install new cotter pin. upper arm x upper ball joint (4 bolts): 29 ft-lbs (39 nm)., plan for a 22mm (castle nut) tool on a M14 stud; final torque is 80 ft-lbs (110 Nm) (upper ball joint nut (steering knuckle x upper ball joint) — gen1 2wd). Sway bar end link (stabilizer bar link) — front tightens to Upper (link to sway bar): 14 ft-lbs | Lower (link to lower arm): 51 ft-lbs ft-lbs (Upper: 19 Nm | Lower: 69 Nm Nm), takes a 14mm / 17mm (use hex on stud to prevent spin) driver, runs on M10 (upper) / M12 (lower) threads, located at the gen1. gen2/gen3 front end links: ~52 ft-lbs. use 6mm hex wrench to hold the stud while tightening the nut.. The lower control arm x frame — gen1 2wd uses a 24mm drive on a M16 thread, torqued to 148 ft-lbs (200 Nm) at the 2wd lower arm to frame (torsion bar suspension). strut bar x frame = 221 ft-lbs.. At the rear anti-sway bar bracket to axle housing. rear link to frame = 14 ft-lbs., the rear sway bar bracket x axle housing torques to 14 ft-lbs (19 Nm) (12mm drive, M8 thread). For the rack end lock nut (gen1 4wd/prerunner and gen2): 41 ft-lbs. use cotter pin on castellated models., plan for a 19mm tool on a M12 stud; final torque is 40 ft-lbs (54 Nm) (tie rod end nut (tie rod end lock nut) — gen1 2wd). Rear shock absorber lower mount x axle housing tightens to 4WD/PreRunner: 53 ft-lbs | 2WD: 19 ft-lbs ft-lbs (4WD: 71 Nm | 2WD: 26 Nm Nm), takes a 21mm driver, runs on M14 threads, located at the gen1. gen2 lower rear shock = 53 ft-lbs. gen3 lower rear shock = 53 ft-lbs..

Body — 2002 Toyota Tacoma

Body fasteners on the 2002 Toyota Tacoma. At the frame rail, the bed mounting bolt torques to 37 ft-lbs (14mm drive, M10x1.25 thread). For the no specific fsm torque value. per toyota technician and forum data: 50–60 ft-lbs with anti-seize or blue loctite. gen2 and gen3 share same bed mount design. 4 to 6 bed bolts per side. check for corrosion on older trucks before removal., plan for a 19mm or 22mm (varies by year) tool on a M14 x 2.0 stud; final torque is 50–60 ft-lbs (OEM spec not formally published) ft-lbs (68–81 Nm Nm) (bed mount bolts (cargo bed x frame)). Cab mount bolts (body-to-frame) tightens to 50–60 ft-lbs (OEM spec not formally published in FSM) ft-lbs (68–81 Nm Nm), takes a 22mm driver, runs on M14 x 2.0 threads, located at the no explicit torque value found in gen1/gen2/gen3 toyota fsm. community consensus and toyota technician guidance: 50–60 ft-lbs with blue loctite. use anti-seize on threads to prevent corrosion bonding (especially gen1 older trucks). apply in a cross-pattern from center outward.. The transfer case skid plate bolt uses a 14mm drive on a M10x1.25 thread, torqued to 29 ft-lbs at the frame. At the frame, the trd skid plate bolt torques to 29 ft-lbs (14mm drive, M10x1.25 thread).

Transmission — 2002 Toyota Tacoma

Transmission fasteners on the 2002 Toyota Tacoma. For the transmission pan, plan for a 24mm tool on a M20x1.5 stud; final torque is 29 ft-lbs (transmission drain plug). Transmission pan bolt tightens to 7 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the transmission pan.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2002 Toyota Tacoma numbers above.

Loading the interactive 2002 Toyota Tacoma fastener lookup with per-bolt filtering, part links, and torque tools…