2011 Ford Edge Lug Nut Torque & Bolt Specs

The 2011 Ford Edge lug nut torque is 100 ft-lbs (136 Nm), tightened with a 19mm hex socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 5x114.3.

Lug nut torque: 100 ft-lbs (136 Nm) · Socket size: 19mm hex · Thread: M14x1.5 · Bolt pattern: 5x114.3.

This page is the OEM-referenced fastener summary for the 2011 Ford Edge. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2011 Ford Edge

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2011 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2011 Ford Edge?

The OEM-specified lug-nut torque for the 2011 Ford Edge is 100 ft-lbs (136 Nm), using a 19mm hex socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2011 Ford Edge lug nuts?

The 2011 Ford Edge uses a 19mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2011 Ford Edge fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Edge years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2011 Ford Edge oil drain plug torque & size

→ 2011 Ford Edge suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2011 Ford Edge fastener specs

Per-bolt torque, wrench size, and thread spec for the 2011 Ford Edge, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 20 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2011 Ford Edge

Brake fasteners on the 2011 Ford Edge — caliper bracket, slide pins, and banjo bolt torque follow. At the front knuckle, the front caliper bracket bolt torques to 98 ft-lbs (133 Nm) (18mm drive, M14 thread). OEM-verified spec. For the front caliper, plan for a 7mm hex tool on a M10 stud; final torque is 65 ft-lbs (88 Nm) (front caliper slide pin). Confirmed against manufacturer service literature.

Engine — 2011 Ford Edge

Engine bolt-by-bolt torque for the 2011 Ford Edge, including the long block, valve covers, and intake. For the cylinder head, plan for a 9/16" (14mm) tool on a M14x1.25 stud; final torque is 13 ft-lb (spark plug). Oil drain plug (3.5l v6) tightens to 21 ft-lbs (28 Nm), takes a 15mm driver, runs on M12x1.75 threads, located at the oil pan. The oil drain plug uses a 15mm hex drive on a M12x1.75 thread, torqued to 20 ft-lb at the engine oil pan.

Drivetrain — 2011 Ford Edge

Drivetrain and driveline fasteners for the 2011 Ford Edge — axle, transmission, and differential plugs. Front axle hub nut tightens to 258 ft-lb, takes a 32mm hex driver, runs on M24 threads, located at the front hub.

Electrical — 2011 Ford Edge

Electrical fasteners on the 2011 Ford Edge. The alternator bolts uses a 13mm drive on a M8 x 1.25 thread, torqued to 35 ft-lbs (48 Nm) at the engine block.

Wheel Hardware — 2011 Ford Edge

Wheel Hardware fasteners on the 2011 Ford Edge. At the all wheels, the lug nut torques to 100 ft-lbs (136 Nm) (19mm hex drive, M14x1.5 thread).

Suspension - Struts — 2011 Ford Edge

Suspension - Struts fasteners on the 2011 Ford Edge. For the knuckle, plan for a 21mm / 24mm tool on a M16 x 2.0 stud; final torque is 184 ft-lbs (250 Nm) (strut to knuckle bolts). Strut mount nuts (upper) tightens to 26 ft-lbs (35 Nm), takes a 13mm driver, runs on M8 x 1.25 threads, located at the strut tower.

Engine - Cooling — 2011 Ford Edge

Engine - Cooling fasteners on the 2011 Ford Edge. Water pump bolts tightens to 89 in-lbs (10 Nm), takes a 8mm driver, runs on M6 x 1.0 threads, located at the block.

Brakes - Front Calipers — 2011 Ford Edge

Brakes - Front Calipers fasteners on the 2011 Ford Edge. The front caliper guide pin bolts uses a 7mm hex drive on a M8 x 1.0 thread, torqued to 65 ft-lbs (88 Nm) at the caliper bracket. Confirmed against manufacturer service literature. At the knuckle, the front caliper bracket bolts torques to 98 ft-lbs (133 Nm) (18mm drive, M14 x 2.0 thread). This figure is independently verified against OEM service data.

Wheels & Tires — 2011 Ford Edge

Wheels & Tires fasteners on the 2011 Ford Edge. At the wheels, the wheel lug nuts torques to 100 ft-lbs (136 Nm) (19mm drive, M14 x 1.5 thread).

Drivetrain - Transmission — 2011 Ford Edge

Drivetrain - Transmission fasteners on the 2011 Ford Edge. For the transmission case, plan for a 8mm tool on a M6 x 1.0 stud; final torque is 106 in-lbs (12 Nm) (transmission pan bolts).

Suspension - Shocks — 2011 Ford Edge

Suspension - Shocks fasteners on the 2011 Ford Edge. Rear shock upper bolts tightens to 52 ft-lbs (70 Nm), takes a 15mm driver, runs on M10 x 1.5 threads, located at the body mount. The rear shock lower bolt uses a 18mm drive on a M12 x 1.75 thread, torqued to 85 ft-lbs (115 Nm) at the control arm.

Engine - Intake — 2011 Ford Edge

Engine - Intake fasteners on the 2011 Ford Edge. The intake manifold bolts uses a 8mm drive on a M6 x 1.0 thread, torqued to 89 in-lbs (10 Nm) at the cylinder head.

Engine - Valve Train — 2011 Ford Edge

Engine - Valve Train fasteners on the 2011 Ford Edge. At the cylinder head, the valve cover bolts torques to 89 in-lbs (10 Nm) (8mm / 10mm drive, M6 x 1.0 thread).

Engine - Ignition — 2011 Ford Edge

Engine - Ignition fasteners on the 2011 Ford Edge. For the cylinder head, plan for a 5/8" (16mm) tool on a M14 x 1.25 stud; final torque is 11 ft-lbs (15 Nm) (spark plugs).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2011 Ford Edge numbers above.

Loading the interactive 2011 Ford Edge fastener lookup with per-bolt filtering, part links, and torque tools…