2015 Ford Edge Lug Nut Torque & Bolt Specs

The 2015 Ford Edge lug nut torque is 150 ft-lbs (203 Nm), tightened with a 19mm hex socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 150 ft-lbs (203 Nm) · Socket size: 19mm hex · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2015 Ford Edge. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2015 Ford Edge

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2015 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2015 Ford Edge?

The OEM-specified lug-nut torque for the 2015 Ford Edge is 150 ft-lbs (203 Nm), using a 19mm hex socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2015 Ford Edge lug nuts?

The 2015 Ford Edge uses a 19mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2015 Ford Edge fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Edge years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2015 Ford Edge suspension & steering torque specs (control arm, ball joint, tie rod)

All 19 2015 Ford Edge fastener specs

Per-bolt torque, wrench size, and thread spec for the 2015 Ford Edge, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 9 of the 19 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2015 Ford Edge

Brake fasteners on the 2015 Ford Edge — caliper bracket, slide pins, and banjo bolt torque follow. At the front knuckle, the front caliper bracket bolt torques to 122 ft-lbs (165 Nm) (18mm hex drive, M14 thread). OEM-verified spec. For the front caliper, plan for a 13mm hex tool on a M10 stud; final torque is 44 ft-lbs (60 Nm) (front caliper slide pin). Confirmed against manufacturer service literature.

Engine — 2015 Ford Edge

Engine bolt-by-bolt torque for the 2015 Ford Edge, including the long block, valve covers, and intake. For the engine oil pan, plan for a 15mm hex tool on a M12x1.75 stud; final torque is 20 ft-lbs (27 Nm) (oil drain plug). Confirmed against manufacturer service literature. Spark plug tightens to 11 ft-lbs (15 Nm), takes a 9/16" (14mm) driver, runs on M14x1.25 threads, located at the cylinder head. This figure is independently verified against OEM service data.

Drivetrain — 2015 Ford Edge

Drivetrain and driveline fasteners for the 2015 Ford Edge — axle, transmission, and differential plugs. Front axle hub nut tightens to 258 ft-lb, takes a 32mm hex driver, runs on M24 threads, located at the front hub.

Electrical — 2015 Ford Edge

Electrical fasteners on the 2015 Ford Edge. The alternator bolts uses a 13mm drive on a M8 x 1.25 thread, torqued to 35 ft-lbs (48 Nm) at the engine block.

Wheel Hardware — 2015 Ford Edge

Wheel Hardware fasteners on the 2015 Ford Edge. At the all wheels, the lug nut torques to 150 ft-lbs (203 Nm) (19mm hex drive, M14x1.5 thread). Confirmed against manufacturer service literature.

Engine - Ignition — 2015 Ford Edge

Engine - Ignition fasteners on the 2015 Ford Edge. For the cylinder head, plan for a 5/8" (16mm) tool on a M14 x 1.25 stud; final torque is 11 ft-lbs (15 Nm) (spark plugs). This figure is independently verified against OEM service data.

Brakes - Front Calipers — 2015 Ford Edge

Brakes - Front Calipers fasteners on the 2015 Ford Edge. Front caliper bracket bolts tightens to 122 ft-lbs (165 Nm), takes a 18mm driver, runs on M14 x 2.0 threads, located at the knuckle. OEM-verified spec. The front caliper guide pin bolts uses a 13mm drive on a M8 x 1.0 thread, torqued to 44 ft-lbs (60 Nm) at the caliper bracket. Confirmed against manufacturer service literature.

Engine - Cooling — 2015 Ford Edge

Engine - Cooling fasteners on the 2015 Ford Edge. The water pump bolts uses a 8mm drive on a M6 x 1.0 thread, torqued to 89 in-lbs (10 Nm) at the block.

Engine - Valve Train — 2015 Ford Edge

Engine - Valve Train fasteners on the 2015 Ford Edge. At the cylinder head, the valve cover bolts torques to 89 in-lbs (10 Nm) (8mm / 10mm drive, M6 x 1.0 thread).

Drivetrain - Transmission — 2015 Ford Edge

Drivetrain - Transmission fasteners on the 2015 Ford Edge. For the transmission case, plan for a 8mm tool on a M6 x 1.0 stud; final torque is 106 in-lbs (12 Nm) (transmission pan bolts).

Suspension - Shocks — 2015 Ford Edge

Suspension - Shocks fasteners on the 2015 Ford Edge. Rear shock lower bolt tightens to 85 ft-lbs (115 Nm), takes a 18mm driver, runs on M12 x 1.75 threads, located at the control arm. The rear shock upper bolts uses a 15mm drive on a M10 x 1.5 thread, torqued to 52 ft-lbs (70 Nm) at the body mount.

Wheels & Tires — 2015 Ford Edge

Wheels & Tires fasteners on the 2015 Ford Edge. The wheel lug nuts uses a 19mm drive on a M14 x 1.5 thread, torqued to 150 ft-lbs (203 Nm) at the wheels. This figure is independently verified against OEM service data.

Suspension - Struts — 2015 Ford Edge

Suspension - Struts fasteners on the 2015 Ford Edge. At the knuckle, the strut to knuckle bolts torques to 184 ft-lbs (250 Nm) (21mm / 24mm drive, M16 x 2.0 thread). For the strut tower, plan for a 13mm tool on a M8 x 1.25 stud; final torque is 26 ft-lbs (35 Nm) (strut mount nuts (upper)).

Engine - Intake — 2015 Ford Edge

Engine - Intake fasteners on the 2015 Ford Edge. For the cylinder head, plan for a 8mm tool on a M6 x 1.0 stud; final torque is 89 in-lbs (10 Nm) (intake manifold bolts).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2015 Ford Edge numbers above.

Loading the interactive 2015 Ford Edge fastener lookup with per-bolt filtering, part links, and torque tools…